LP8733-Q1 datasheet(7/86 Pages) TI2

7 / 86 page

6.5 Electrical Characteristics (continued)

Limits apply over the junction temperature range –40°C ≤ TJ ≤ +140°C, specified VVANA, VVIN_Bx, VVIN_LDOx, VVOUT_Bx,

VVOUT_LDOx and IOUT range, unless otherwise noted. Typical values are at TJ = 25°C, VVANA = VVIN_Bx = VVIN_LDOx = 3.7 V,

and VOUT = 1 V, unless otherwise noted(1) (2).

PARAMETER

TEST CONDITIONS

MIN

TYP

MAX

UNIT

VOUT_Bx_DC

DC output voltage

accuracy, includes

voltage reference, DC

load and line regulations,

process and temperature

Force PWM mode, VOUT < 1 V

–20

Force PWM mode, VOUT ≥ 1 V

–2%

PFM mode, VOUT < 1 V, the average output

voltage level is increased by max. 20 mV

–20

PFM mode, VOUT ≥ 1 V, the average output

voltage level is increased by max. 20 mV

–2%

2% + 20

Ripple voltage, single-

phase output

PWM mode

mVp-p

PFM mode, IOUT = 10 mA

Ripple voltage, dual-

phase output

PWM mode

mVp-p

PFM mode, IOUT = 10 mA

DCLNR

DC line regulation

IOUT = 1 A

±0.05

%/V

DCLDR

DC load regulation in

PWM mode

VOUT_Bx = 1 V, IOUT from 0 to IOUT(max)

0.3%

TLDSR

Transient load step

response, single-phase

output

IOUT = 0.1 A to 2 A, TR = TF = 400 ns, PWM

mode

±55

Transient load step

response, dual-phase

output

IOUT = 0.1 A to 4 A, TR = TF = 400 ns, PWM

mode

±50

TLNSR

Transient line response

V(VIN_Bx) stepping 3 V ↔ 3.5 V, TR = TF = 10

µs, IOUT = IOUT(max)

±10

ILIM FWD

Forward current limit per

phase (peak for every

switching cycle)

Programmable range

1.5

Step size

0.5

Accuracy, V(VIN_Bx) ≥ 3 V, ILIM = 4 A

–5%

7.5%

20%

Accuracy, 2.8 V ≤ V(VIN_Bx) < 3 V, ILIM = 4 A

–20%

7.5%

20%

ILIM NEG

Negative current limit per

phase

1.6

2.0

3.0

RDS(ON) HS FET

On-resistance, high-side

FET

Each phase, between VIN_Bx and SW_Bx

pins (I = 1 A)

110

mΩ

RDS(ON) LS FET

On-resistance, low-side

FET

Each phase, between SW_Bx and PGND_Bx

pins (I = 1 A)

mΩ

ƒSW

Switching frequency

PWM mode

1.8

2.2

MHz

Current balancing for

dual-phase output

Current mismatch between phases, IOUT > 1

10%

Start-up time (soft start)

From ENx to VOUT_Bx = 0.35 V (slew-rate

control begins)

120

µs

Output voltage slew-

rate(4)

SLEW_RATEx[2:0] = 010, COUT-TOTAL_BUCK <

80 µF per phase

–15%

15%

mV/µs

SLEW_RATEx[2:0] = 011, COUT-TOTAL_BUCK <

130 µF per phase

7.5

SLEW_RATEx[2:0] = 100, COUT-TOTAL_BUCK <

250 µF per phase

3.8

SLEW_RATEx[2:0] = 101, COUT-TOTAL_BUCK

< 500 µF per phase

1.9

SLEW_RATEx[2:0] = 110, COUT-TOTAL_BUCK

< 500 µF per phase

0.94

SLEW_RATEx[2:0] = 111, COUT-TOTAL_BUCK

< 500 µF per phase

0.47

www.ti.com

LP8733-Q1

SNVSB64A – JUNE 2019 – REVISED JUNE 2021

Submit Document Feedback

Product Folder Links: LP8733-Q1

LP8733-Q1 Datasheet(PDF) 7 Page - Texas Instruments

LP8733-Q1 Datasheet(HTML) 7 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86

Datasheet Descarga

Enlace URL