LP8733-Q1 datasheet(45/86 Pages) TI2

45 / 86 page

7.6.1.6 BUCK1_CTRL_2

BUCK1_CTRL_2 is shown in Table 7-19, Address: 0x05

Table 7-18. BUCK1_CTRL_2 Register

Reserved - do not use

BUCK1_ILIM[2:0]

BUCK1_SLEW_RATE[2:0]

Table 7-19. BUCK1_CTRL_2 Register Field Descriptions

Bits

Field

Type

Default

Description

7:6

Reserved - do not

use

R/W

5:3

BUCK1_ILIM[2:0]

R/W

Sets the switch current limit of the Buck1. Can be programmed at any time during

operation:

0x0 - 1.5 A

0x1 - 2.0 A

0x2 - 2.5 A

0x3 - 3.0 A

0x4 - 3.5 A

0x5 - 4.0 A

0x6 - Reserved - do not use.

0x7 - Reserved - do not use.

2:0

BUCK1_SLEW_RA

TE[2:0]

R/W

Sets the output voltage slew rate for the Buck1 regulator (rising and falling edges):

0x0 - Reserved - do not use.

0x1 - Reserved - do not use.

0x2 - 10 mV/µs

0x3 - 7.5 mV/µs

0x4 - 3.8 mV/µs

0x5 - 1.9 mV/µs

0x6 - 0.94 mV/µs

0x7 - 0.47 mV/µs

7.6.1.7 BUCK0_VOUT

BUCK0_VOUT is shown in Table 7-21, Address: 0x06

Table 7-20. BUCK0_VOUT Register

BUCK0_VSET[7:0]

Table 7-21. BUCK0_VOUT Register Field Descriptions

Bits

Field

Type

Default

Description

7:0

BUCK0_VSET[7:0]

R/W

Sets the output voltage of the Buck0 regulator:

Reserved; do not use.

0x00 ... 0x13

0.7 V - 0.73 V, 10 mV steps

0x14 - 0.7V

...

0x17 - 0.73 V

0.73 V - 1.4 V, 5 mV steps

0x18 - 0.735 V

...

0x9D - 1.4 V

1.4 V - 3.36 V, 20 mV steps

0x9E - 1.42 V

...

0xFF - 3.36 V

7.6.1.8 BUCK1_VOUT

BUCK1_VOUT is shown in Table 7-23, Address: 0x07

www.ti.com

LP8733-Q1

SNVSB64A – JUNE 2019 – REVISED JUNE 2021

Submit Document Feedback

Product Folder Links: LP8733-Q1

LP8733-Q1 Datasheet(PDF) 45 Page - Texas Instruments

LP8733-Q1 Datasheet(HTML) 45 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86

Datasheet Descarga

Enlace URL