| Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
UPD360 Datasheet(PDF) 15 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
UPD360 Datasheet(HTML) 15 Page - Microchip Technology |
|
15 / 221 page ![]() 2016-2017 Microchip Technology Inc. DS00002084C-page 15 UPD360 Type-C Attach ATTACH O8 In the Standalone UFP and Standalone DFP modes (UPD360-A/UPD360-B only), this signal indicates that the USB Type-C receptacles at the near and far end of the cable both have a plug-in. This pin is autonomously driven by the device in DFP standalone mode. 0b: Nothing attached 1b: USB Type-C port has an end-end attached Refer to Section 9.10, "Standalone DFP (UPD360-A/ UPD360-B Only)" and Section 9.11, "Standalone UFP (UPD360-A/UPD360-B Only)"for additional information. Note: Float this signal when unused. Note: This signal is not available in the UPD360-C. Type-C Orientation ORIENTATION O8 In the Standalone UFP and Standalone DFP modes (UPD360-A/UPD360-B only), this signal is used to indicate which CC pin is terminated by the attached DFP/UFP and is autonomously driven by the device in DFP standalone mode. DFP: 0b: CC1 pin is terminated by Rd. 1b: CC2 pin is terminated by Rd. UFP: 0b: CC1 pin is pulled to a higher voltage than CC2. 1b: CC2 pin is pulled to a higher voltage than CC1. Refer to Section 9.10, "Standalone DFP (UPD360-A/ UPD360-B Only)" and Section 9.11, "Standalone UFP (UPD360-A/UPD360-B Only)"for additional information. Note: Float this signal when unused. Note: This signal is not available in the UPD360-C. Over-current sense OCS_N OD8 In the Standalone DFP mode (UPD360-A/UPD360-B only), this active-low signal indicates over-current sense. This sig- nal maps to the PPC_INT interrupt. Note: This signal is active-low. Float this signal when unused. Note: This signal is not available in the UPD360-C. VBUS Power Enable PWR_EN IS In the Standalone DFP mode (UPD360-A/UPD360-B only), this signal is used as a port power switch enable for USB hubs. Note: This signal should be tied to the Power Good signal from the VS supply. Note: Tie this signal to ground when unused. Note: This signal is not available in the UPD360-C. TABLE 3-4: BALL DESCRIPTIONS (CONTINUED) NAME SYMBOL BUFFER TYPE DESCRIPTION |
|
Enlace URL |
| ¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Enlace a la hoja de datos | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |