| Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
LAN8808D Datasheet(PDF) 23 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
LAN8808D Datasheet(HTML) 23 Page - Microchip Technology |
|
23 / 80 page ![]() LAN8808D © 2026 Microchip Technology Inc. and its subsidiaries DS00005833C-page 23 3.3.2 PHY ADDRESS (PHYAD[4:0]) The PHYAD[4:0] configuration straps set the base value of the PHY’s management address. The addresses of each of the 4 PHYs are the base value, as defined by PHYAD[4:0], plus offsets of 0, 1, 2 and 3. 3.3.3 LED MODE SELECT (LED_MODE) The LED_MODE configuration strap selects between Individual-LED (pulled-up) or Tri-color-LED (pulled-down) modes. All 8 LEDs are configured with identical behavior. The LED_MODE configuration strap is sampled and latched at power-up/reset and is defined as follows: 0: Tri-color-LED mode 1: Individual-LED mode LED operation is described in Section 5.17, "LEDs". 3.3.4 LED POLARITY (PORT[3:0]_LED[2:1]_POL) The PORT[3:0]_LED[2:1]_POL configuration straps set the default polarity of the LED pins. When a LED pin is used as a function mode strap (for example a PHY address bit), the default LED pin polarity is automatically selected based on the inverse of the strap value. A LED, via a resistor, is then used as a pull-up or pull-down. This is shown in Figure 3-2. LED operation is described in Section 5.17, "LEDs". 01111 RESERVED 11110 RESERVED FIGURE 3-2: STRAP ON LED WITH POLARITY TABLE 3-9: DEVICE MODE SELECTIONS (CONTINUED) Legend: 1000FD = 1000BASE-T Full Duplex 100FD = 100BASE-TX Full Duplex 100HD = 100BASE-TX Half Duplex 10FD = 10BASE-T Full Duplex 10HD = 10BASE-T Half Duplex “X” means “is advertised by auto-negotiation” (for example 10BT FD and 10BT HD are both available auto-negotiation results when MODE_SEL = 10000). Functional Strap = 0 LED Output = Active High (LEDPOL Strap = 1) VDDIO Functional Strap = 1 LED Output = Active Low (LEDPOL Strap = 0) LED/Strap Pin LED/Strap Pin Supplemental resistor to ensure a valid low level during strap load 220 220 10 k 10 k Supplemental resistor to ensure a valid high level during strap load |
|
Enlace URL |
| ¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Enlace a la hoja de datos | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |