PIC17C44 datasheet(72/241 Pages) MICROCHIP

72 / 241 page

PIC17C4X

DS30412C-page 72

FIGURE 12-2: TCON2 REGISTER (ADDRESS: 17h, BANK 3)

R - 0

R/W - 0

CA2OVF CA1OVF PWM2ON PWM1ON CA1/PR3 TMR3ON TMR2ON TMR1ON

R = Readable bit

W = Writable bit

-n = Value at POR reset

bit7

bit0

bit 7:

CA2OVF: Capture2 Overﬂow Status bit

This bit indicates that the capture value had not been read from the capture register pair (CA2H:CA2L)

before the next capture event occurred. The capture register retains the oldest unread capture value (last

capture before overﬂow). Subsequent capture events will not update the capture register with the Timer3

value until the capture register has been read (both bytes).

1 = Overﬂow occurred on Capture2 register

0 = No overﬂow occurred on Capture2 register

bit 6:

CA1OVF: Capture1 Overﬂow Status bit

This bit indicates that the capture value had not been read from the capture register pair

(PR3H/CA2H:PR3L/CA2L) before the next capture event occurred. The capture register retains the old-

est unread capture value (last capture before overﬂow). Subsequent capture events will not update the

capture register with the TMR3 value until the capture register has been read (both bytes).

1 = Overﬂow occurred on Capture1 register

0 = No overﬂow occurred on Capture1 register

bit 5:

PWM2ON: PWM2 On bit

1 = PWM2 is enabled (The RB3/PWM2 pin ignores the state of the DDRB<3> bit)

0 = PWM2 is disabled (The RB3/PWM2 pin uses the state of the DDRB<3> bit for data direction)

bit 4:

PWM1ON: PWM1 On bit

1 = PWM1 is enabled (The RB2/PWM1 pin ignores the state of the DDRB<2> bit)

0 = PWM1 is disabled (The RB2/PWM1 pin uses the state of the DDRB<2> bit for data direction)

bit 3:

CA1/PR3: CA1/PR3 Register Mode Select bit

1 = Enables Capture1 (PR3H/CA1H:PR3L/CA1L is the Capture1 register. Timer3 runs without

a period register)

0 = Enables the Period register (PR3H/CA1H:PR3L/CA1L is the Period register for Timer3)

bit 2:

TMR3ON: Timer3 On bit

1 = Starts Timer3

0 = Stops Timer3

bit 1:

TMR2ON: Timer2 On bit

This bit controls the incrementing of the Timer2 register. When Timer2:Timer1 form the 16-bit timer (T16

is set), TMR2ON must be set. This allows the MSB of the timer to increment.

1 = Starts Timer2 (Must be enabled if the T16 bit (TCON1<3>) is set)

0 = Stops Timer2

bit 0:

TMR1ON: Timer1 On bit

When T16 is set (in 16-bit Timer Mode)

1 = Starts 16-bit Timer2:Timer1

0 = Stops 16-bit Timer2:Timer1

When T16 is clear (in 8-bit Timer Mode)

1 = Starts 8-bit Timer1

0 = Stops 8-bit Timer1

PIC17C44 Datasheet(PDF) 72 Page - Microchip Technology

PIC17C44 Datasheet(HTML) 72 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Descarga

Enlace URL