ATmega48 datasheet(102/340 Pages) ATMEL

102 / 340 page

102

7530H–AVR–02/09

ATmega48/88/168 Automotive

12.8.6

Timer/Counter Interrupt Mask Register – TIMSK0

• Bits 7..3 – Res: Reserved Bits

These bits are reserved bits in the ATmega48/88/168 and will always read as zero.

• Bit 2 – OCIE0B: Timer/Counter Output Compare Match B Interrupt Enable

When the OCIE0B bit is written to one, and the I-bit in the Status Register is set, the

Timer/Counter Compare Match B interrupt is enabled. The corresponding interrupt is executed if

a Compare Match in Timer/Counter occurs, i.e., when the OCF0B bit is set in the Timer/Counter

Interrupt Flag Register – TIFR0.

• Bit 1 – OCIE0A: Timer/Counter0 Output Compare Match A Interrupt Enable

When the OCIE0A bit is written to one, and the I-bit in the Status Register is set, the

Timer/Counter0 Compare Match A interrupt is enabled. The corresponding interrupt is executed

if a Compare Match in Timer/Counter0 occurs, i.e., when the OCF0A bit is set in the

Timer/Counter 0 Interrupt Flag Register – TIFR0.

• Bit 0 – TOIE0: Timer/Counter0 Overflow Interrupt Enable

When the TOIE0 bit is written to one, and the I-bit in the Status Register is set, the

Timer/Counter0 Overflow interrupt is enabled. The corresponding interrupt is executed if an

overflow in Timer/Counter0 occurs, i.e., when the TOV0 bit is set in the Timer/Counter 0 Inter-

rupt Flag Register – TIFR0.

12.8.7

Timer/Counter 0 Interrupt Flag Register – TIFR0

• Bits 7..3 – Res: Reserved Bits

These bits are reserved bits in the ATmega48/88/168 and will always read as zero.

• Bit 2 – OCF0B: Timer/Counter 0 Output Compare B Match Flag

The OCF0B bit is set when a Compare Match occurs between the Timer/Counter and the data in

OCR0B – Output Compare Register0 B. OCF0B is cleared by hardware when executing the cor-

responding interrupt handling vector. Alternatively, OCF0B is cleared by writing a logic one to

the flag. When the I-bit in SREG, OCIE0B (Timer/Counter Compare B Match Interrupt Enable),

and OCF0B are set, the Timer/Counter Compare Match Interrupt is executed.

• Bit 1 – OCF0A: Timer/Counter 0 Output Compare A Match Flag

The OCF0A bit is set when a Compare Match occurs between the Timer/Counter0 and the data

in OCR0A – Output Compare Register0. OCF0A is cleared by hardware when executing the cor-

responding interrupt handling vector. Alternatively, OCF0A is cleared by writing a logic one to

the flag. When the I-bit in SREG, OCIE0A (Timer/Counter0 Compare Match Interrupt Enable),

and OCF0A are set, the Timer/Counter0 Compare Match Interrupt is executed.

Bit

7654

––––

–

OCIE0B

OCIE0A

TOIE0

TIMSK0

Read/Write

R/W

Initial Value

0000

Bit

76543210

–––––

OCF0B

OCF0A

TOV0

TIFR0

Read/Write

RRRRR

R/W

Initial Value

00000000

ATmega48 Datasheet(PDF) 102 Page - ATMEL Corporation

ATmega48 Datasheet(HTML) 102 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Descarga

Enlace URL