STM32G47PBY6TR datasheet(23/229 Pages) STMICROELECTRONICS

23 / 229 page

DS12712 Rev 3

23/229

STM32G473xB STM32G473xC STM32G473xE

Functional overview

3.11.4

Low-power modes

By default, the microcontroller is in Run mode after system or power Reset. It is up to the

user to select one of the low-power modes described below:

•

Sleep mode: In Sleep mode, only the CPU is stopped. All peripherals continue to

operate and can wake up the CPU when an interrupt/event occurs.

•

Low-power run mode: This mode is achieved with VCORE supplied by the low-power

regulator to minimize the regulator's operating current. The code can be executed from

SRAM or from Flash, and the CPU frequency is limited to 2 MHz. The peripherals with

independent clock can be clocked by HSI16.

•

Low-power sleep mode: This mode is entered from the low-power run mode. Only the

CPU clock is stopped. When wakeup is triggered by an event or an interrupt, the

system reverts to the Low power run mode.

•

Stop mode: In Stop mode, the device achieves the lowest power consumption while

retaining the SRAM and register contents. All clocks in the VCORE domain are

stopped. The PLL, as well as the HSI16 RC oscillator and the HSE crystal oscillator are

disabled. The LSE or LSI keep running. The RTC can remain active (Stop mode with

RTC, Stop mode without RTC). Some peripherals with wakeup capability can enable

the HSI16 RC during Stop mode, so as to get clock for processing the wakeup event.

•

Standby mode: The Standby mode is used to achieve the lowest power consumption

with brown-out reset, BOR. The internal regulator is switched off to power down the

VCORE domain. The PLL, as well as the HSI16 RC oscillator and the HSE crystal

oscillator are also powered down. The RTC can remain active (Standby mode with

RTC, Standby mode without RTC). The BOR always remains active in Standby mode.

For each I/O, the software can determine whether a pull-up, a pull-down or no resistor

shall be applied to that I/O during Standby mode. Upon entering Standby mode, SRAM

and register contents are lost except for registers in the RTC domain and standby

circuitry. The device exits Standby mode upon external reset event (NRST pin), IWDG

reset event, wakeup event (WKUP pin, configurable rising or falling edge) or RTC

event (alarm, periodic wakeup, timestamp, tamper), or when a failure is detected on

LSE (CSS on LSE).

•

Shutdown mode: The Shutdown mode allows to achieve the lowest power

consumption. The internal regulator is switched off to power down the VCORE domain.

The PLL, as well as the HSI16 and LSI RC-oscillators and HSE crystal oscillator are

also powered down. The RTC can remain active (Shutdown mode with RTC, Shutdown

mode without RTC). The BOR is not available in Shutdown mode. No power voltage

monitoring is possible in this mode. Therefore, switching to RTC domain is not

supported. SRAM and register contents are lost except for registers in the RTC

domain. The device exits Shutdown mode upon external reset event (NRST pin),

IWDG reset event, wakeup event (WKUP pin, configurable rising or falling edge) or

RTC event (alarm, periodic wakeup, timestamp, tamper).

3.11.5

Reset mode

In order to improve the consumption under reset, the I/Os state under and after reset is

“analog state” (the I/O schmitt trigger is disabled). In addition, the internal reset pull-up is

deactivated when the reset source is internal.

STM32G47PBY6TR Datasheet(PDF) 23 Page - STMicroelectronics

STM32G47PBY6TR Datasheet(HTML) 23 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Descarga

Enlace URL