RMLD232UAW datasheet(3/50 Pages) EMLSI

3 / 50 page

Rev 0.7

64Mb Low Power DDR SDRAM

Advanced

Input/Output Function Description

SYMBOL

TYPE

DESCRIPTION

CK, CK

Input

Clock : CK and CK are differential clock inputs. All address and control input signals are sam-

pled on the crossing of the positive edge of CK and negative edge of CK. Internal clock signals

are derived from CK/CK.

CKE

Input

Clock Enable : CKE HIGH activates, and CKE LOW deactivates internal clock signals, and

device input buffers and output drivers. Taking CKE LOW provides PRECHARGE POWER-

DOWN and SELF REFRESH operation (all banks idle), or ACTIVE POWER-DOWN (row

ACTIVE in any bank). CKE is synchronous for all funtions except for disabling outputs, which

is achieved asynchronously. Input buffers, excluding CK, CK and CKE , are disabled during

power-down and self refresh mode which are contrived for low standby power consumption.

Input

Chip Select : CS enables(registered LOW) and disables(registered HIGH) the command

decoder. All commands are masked when CS is registered HIGH. CS provides for external

bank selection on systems with multiple banks. CS is considered part of the command code.

RAS, CAS, WE

Input

Command Inputs : RAS, CAS and WE (along with CS) define the command being entered.

*1DM0, DM1

DM2, DM3

Input

Input Data Mask : DM is an input mask signal for write data. Input data is masked when DM is

sampled HIGH along with that input data during a WRITE access. DM is sampled on both

edges of DQS. DM pins include dummy loading internally, to matches the DQ and DQS load-

ing. For the x32, DM0 corresponds to the data on DQ0-DQ7 ; DM1 corresponds to the data on

DQ8-DQ15 ;DM2 corresponds to the data on DQ16-DQ23 ; DM3 corresponds to the data on

DQ24-DQ31 .

BA0,BA1

Input

Bank Address Inputs : BA0 and BA1 define to which bank an ACTIVE, READ, WRITE or PRE-

CHARGE command is being applied.

A [n : 0]

Input

Address Inputs : Provide the row address for ACTIVE commands, and the column address

and AUTO PRECHARGE bit for READ/WRITE commands, to select one location out of the

memory array in the respective bank. A10 sampled during a PRECHARGE command deter-

mines wherther the PRECHARGE applies to one bank (A10 LOW) or all banks (A10 HIGH). If

only one bank is to be precharged, the bank is selected by BA0,BA1. The address inputs also

provide the op-code during a MODE REGISTER SET command. BA0 and BA1 determines

which mode register( mode register or extended mode register ) is loaded during the MODE

*1DQ

I/O

Data Input/Output : Data bus

*1DQS0, DQS1

DQS2, DQS3

I/O

Data Strobe : Output with read data, input with write data. Edge-aligned with read data, cen-

tered in write data. It is used to fetch write data. For the x32, DQS0 corresponds to the data on

DQ0-DQ7 ; DQS1 corresponds to the data on DQ8-DQ15 ;DQS2 corresponds to the data on

DQ16-DQ23 ; DQS3 corresponds to the data on DQ24-DQ31.

No Connect : No internal electrical connection is present.

VDDQ

Supply

DQ Power Supply : 1.7V to 1.95V.

VSSQ

Supply

DQ Ground.

VDD

Supply

Power Supply : 1.7V to 1.95V.

VSS

Supply

Ground.

RMLD232UAW Datasheet(PDF) 3 Page - Emerging Memory & Logic Solutions Inc

RMLD232UAW Datasheet(HTML) 3 Page - Emerging Memory & Logic Solutions Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

Datasheet Descarga

Enlace URL