CC1150-RTR1 datasheet(7/67 Pages) TI1

7 / 67 page

CC1150

www.ti.com

SWRS037B – JANUARY 2006 – REVISED MARCH 2015

4.5

Current Consumption

Tc = 25°C, VDD = 3.0 V if nothing else stated. All measurement results are obtained using the CC1150EM reference design

(see [1] and [2]).

PARAMETER

TYP

UNIT

CONDITION

200

Voltage regulator to digital part off, register values lost (SLEEP state)

Voltage regulator to digital part on, all other modules in power down

222

µA

(XOFF state)

Only voltage regulator to digital part and crystal oscillator running

1.1

Current consumption

(IDLE state)

Only the frequency synthesizer running (FSTXON state). This

current consumption also representative for the other intermediate

7.7

states when going from IDLE until reaching TX, and frequency

calibration states

25.6

Transmit mode, +10 dBm output power (0xC4)

Current consumption, 315 MHz

14.1

Transmit mode, 0 dBm output power (0x60)

See more in Section 5.16 and DN012 [3].

26.1

Transmit mode, +10 dBm output power (0xC2)

Current consumption, 433 MHz

14.6

Transmit mode, 0 dBm output power (0x60)

See more in Section 5.16 and DN012 [3].

29.3

Transmit mode, +10 dBm output power (0xC3)

Current consumption, 868 MHz

15.5

Transmit mode, 0 dBm output power (0x60)

See more in Section 5.16 and DN012 [3].

29.3

Transmit mode, +10 dBm output power (0xC0)

Current consumption, 915 MHz

15.2

Transmit mode, 0 dBm output power (0x50)

See more in Section 5.16 and DN012 [3].

4.6

RF Transmit

Tc = 25°C, VDD = 3.0 V, if nothing else stated. All measurement results are obtained using the CC1150EM reference design

(see [1] and [2]).

PARAMETER

TYP

MAX

UNIT

CONDITION

315 MHz

122 + j31

Differential impedance as seen from the RF-

Differential load

433 MHz

116 + j41

port (RF_P and RF_N) towards the antenna.

impedance

Follow the CC1150EM reference design

86.5 +

868/915 MHz

(see [1] and [2]).

j43

Output power is programmable, and full

range is available across all frequency

bands. Output power may be restricted by

regulatory limits. See also

DN006 [5].

Delivered to a 50-

Ω single-ended load via

Output power, highest setting

+10

dBm

CC1150 EM reference design (see [1] and

[2]) RF matching network. Maximum output

power can be increased 1 to 2 dB by using

wire-wound inductors instead of multilayer

inductors in the balun and filter circuit for the

868/915 MHz band, see more in DN017 [6].

Output power is programmable, and full

range is available across all frequency

bands.

Output power, lowest setting

–30

dBm

Delivered to a 50

Ω single-ended load via

CC1150 EM reference design (see [1] and

[2]) RF matching network.

Specifications

Submit Documentation Feedback

Product Folder Links: CC1150

CC1150-RTR1 Datasheet(PDF) 7 Page - Texas Instruments

CC1150-RTR1 Datasheet(HTML) 7 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67

Datasheet Descarga

Enlace URL