MPC5634MF0MMGA8 datasheet(16/118 Pages) FREESCALE

16 / 118 page

MPC5634M Microcontroller Data Sheet, Rev. 4

Preliminary—Subject to Change Without Notice

Overview

Freescale Semiconductor

— Glitch detection on reset input

— Software controlled reset assertion

•

External interrupt

— 11 interrupt requests

— Rising or falling edge event detection

— Programmable digital filter for glitch rejection

— Critical Interrupt request

— Non-Maskable Interrupt request

•GPIO

— GPIO function on 80 I/O pins

— Virtual GPIO on 64 I/O pins via DSPI serialization (requires external deserialization device)

— Dedicated input and output registers for setting each GPIO and Virtual GPIO pin

•

Internal multiplexing

— Allows serial and parallel chaining of DSPIs

— Allows flexible selection of eQADC trigger inputs

— Allows selection of interrupt requests between external pins and DSPI

1.3.8

ECSM

The error correction status module provides status information regarding platform memory errors reported by error-correcting

codes.

1.3.9

Flash

Devices in the MPC5634M family provide up to 1.5 MB of programmable, non-volatile, flash memory. The non-volatile

memory (NVM) can be used for instruction and/or data storage. The flash module includes a Fetch Accelerator, that optimizes

the performance of the flash array to match the CPU architecture and provides single cycle random access to the flash @

80 MHz. The flash module interfaces the system bus to a dedicated flash memory array controller. For CPU ‘loads’, DMA

transfers and CPU instruction fetch, it supports a 64-bit data bus width at the system bus port, and a 128-bit read data interface

to flash memory. The module contains a four-entry, 128-bit prefetch buffer and a prefetch controller which prefetches sequential

lines of data from the flash array into the buffer. Prefetch buffer hits allow no-wait responses. Normal flash array accesses are

registered and are forwarded to the system bus on the following cycle, incurring three wait-states. Prefetch operations may be

automatically controlled, and are restricted to instruction fetch.

The flash memory provides the following features:

•

Supports a 64-bit data bus for instruction fetch, CPU loads and DMA access. Byte, halfword, word and doubleword

reads are supported. Only aligned word and doubleword writes are supported.

•

Fetch Accelerator

— Architected to optimize the performance of the flash with the CPU to provide single cycle random access to the

flash up to 80 MHz system clock speed

— Configurable read buffering and line prefetch support

— Four line read buffers (128 bits wide) and a prefetch controller

•

Hardware and software configurable read and write access protections on a per-master basis

•

Interface to the flash array controller is pipelined with a depth of one, allowing overlapped accesses to proceed in

parallel for interleaved or pipelined flash array designs

•

Configurable access timing allowing use in a wide range of system frequencies

•

Multiple-mapping support and mapping-based block access timing (0-31 additional cycles) allowing use for emulation

of other memory types

MPC5634MF0MMGA8 Datasheet(PDF) 16 Page - Freescale Semiconductor, Inc

MPC5634MF0MMGA8 Datasheet(HTML) 16 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Descarga

Enlace URL