LPC47M14X datasheet(83/205 Pages) SMSC

83 / 205 page

SMSC DS – LPC47M14X

Page 83

Rev. 03/19/2001

EPP 1.7 Read

The timing for a read operation (data) is shown in timing diagram EPP 1.7 Read Data cycle. The chip inserts wait states

into the I/O read cycle when nWAIT is active low during the EPP cycle. This can be used to extend the cycle time. The

read cycle can complete when nWAIT is inactive high.

Read Sequence of Operation

The host sets PDIR bit in the control register to a logic "1". This deasserts nWRITE and tri-states the PData

bus.

The host initiates an I/O read cycle to the selected EPP register.

Chip asserts nDATASTB or nADDRSTRB indicating that PData bus is tri-stated, PDIR is set and the nWRITE

signal is valid.

If nWAIT is asserted, the chip inserts wait states into the I/O read cycle until the peripheral deasserts nWAIT or

a time-out occurs.

The Peripheral drives PData bus valid.

The Peripheral deasserts nWAIT, indicating that PData is valid and the chip may begin the termination phase

of the cycle.

The chip drives the final sync and deasserts nDATASTB or nADDRSTRB.

Peripheral tri-states the PData bus.

Chip may modify nWRITE, PDIR and nPDATA in preparation of the next cycle.

Table 41 – EPP Pin Descriptions

EPP

SIGNAL

EPP NAME

TYPE

EPP DESCRIPTION

nWRITE

nWrite

This signal is active low. It denotes a write operation.

PD<0:7>

Address/Data

I/O

Bi-directional EPP byte wide address and data bus.

INTR

Interrupt

This signal is active high and positive edge triggered. (Pass

through with no inversion, Same as SPP).

nWAIT

nWait

This signal is active low.

It is driven inactive as a positive

acknowledgement from the device that the transfer of data is

completed. It is driven active as an indication that the device is

ready for the next transfer.

nDATASTB

nData Strobe

This signal is active low. It is used to denote data read or write

operation.

nRESET

nReset

This signal is active low. When driven active, the EPP device

is reset to its initial operational mode.

nADDRSTB

Address

Strobe

This signal is active low. It is used to denote address read or

write operation.

Paper End

Same as SPP mode.

SLCT

Printer

Selected

Status

Same as SPP mode.

nERR

Error

Same as SPP mode.

Note 1: SPP and EPP can use 1 common register.

Note 2: nWrite is the only EPP output that can be over-ridden by SPP control port during an EPP cycle. For correct

EPP read cycles, PCD is required to be a low.

LPC47M14X Datasheet(PDF) 83 Page - SMSC Corporation

LPC47M14X Datasheet(HTML) 83 Page - SMSC Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Descarga

Enlace URL