AT25DF081A datasheet(3/54 Pages) ETC2

3 / 54 page

8715C–SFLSH–1/2013

AT25DF081A

Pin Descriptions and Pinouts

Table 2-1.

Pin Descriptions

Symbol

Name and Function

Asserted

State

Type

CHIP SELECT: Asserting the CS pin selects the device. When the CS pin is deasserted, the

device will be deselected and normally be placed in standby mode (not Deep Power-Down

mode), and the SO pin will be in a high-impedance state. When the device is deselected,

data will not be accepted on the SI pin.

A high-to-low transition on the CS pin is required to start an operation, and a low-to-high

transition is required to end an operation. When ending an internally self-timed operation

such as a program or erase cycle, the device will not enter the standby mode until the

completion of the operation.

Low

Input

SCK

SERIAL CLOCK: This pin is used to provide a clock to the device and is used to control the

flow of data to and from the device. Command, address, and input data present on the SI pin

is always latched in on the rising edge of SCK, while output data on the SO pin is always

clocked out on the falling edge of SCK.

Input

SI (SIO)

SERIAL INPUT (SERIAL INPUT/OUTPUT): The SI pin is used to shift data into the device.

The SI pin is used for all data input including command and address sequences. Data on the

SI pin is always latched in on the rising edge of SCK.

With the Dual-Output Read Array command, the SI pin becomes an output pin (SIO) to allow

two bits of data (on the SO and SIO pins) to be clocked out on every falling edge of SCK. To

maintain consistency with SPI nomenclature, the SIO pin will be referenced as SI throughout

the document with exception to sections dealing with the Dual-Output Read Array command

in which it will be referenced as SIO.

Data present on the SI pin will be ignored whenever the device is deselected (CS is

deasserted).

Input/Output

SO (SOI)

SERIAL OUTPUT (SERIAL OUTPUT/INPUT): The SO pin is used to shift data out from the

device. Data on the SO pin is always clocked out on the falling edge of SCK.

With the Dual-Input Byte/Page Program command, the SO pin becomes an input pin (SOI)

to allow two bits of data (on the SOI and SI pins) to be clocked in on every rising edge of

SCK. To maintain consistency with SPI nomenclature, the SOI pin will be referenced as SO

throughout the document with exception to sections dealing with the Dual-Input Byte/Page

Program command in which it will be referenced as SOI.

The SO pin will be in a high-impedance state whenever the device is deselected (CS is

deasserted).

Output/Input

WRITE PROTECT: The WP pin controls the hardware locking feature of the device. Please

refer to “Protection Commands and Features” on page 17 for more details on protection

features and the WP pin.

The WP pin is internally pulled-high and may be left floating if hardware controlled protection

will not be used. However, it is recommended that the WP pin also be externally connected

to VCC whenever possible.

Low

Input

HOLD

HOLD: The HOLD pin is used to temporarily pause serial communication without

deselecting or resetting the device. While the HOLD pin is asserted, transitions on the SCK

pin and data on the SI pin will be ignored, and the SO pin will be in a high-impedance state.

The CS pin must be asserted, and the SCK pin must be in the low state in order for a Hold

condition to start. A Hold condition pauses serial communication only and does not have an

effect on internally self-timed operations such as a program or erase cycle. Please refer to

“Hold” on page 41 for additional details on the Hold operation.

The HOLD pin is internally pulled-high and may be left floating if the Hold function will not be

used. However, it is recommended that the HOLD pin also be externally connected to VCC

whenever possible.

Low

Input

AT25DF081A Datasheet(PDF) 3 Page - List of Unclassifed Manufacturers

AT25DF081A Datasheet(HTML) 3 Page - List of Unclassifed Manufacturers

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54

Datasheet Descarga

Enlace URL