ADP5586ACBZ-00-R7 datasheet(37/44 Pages) AD

37 / 44 page

Data Sheet

ADP5586

Rev. 0 | Page 37 of 44

PULSE_GEN_CONFIG, Register 0x35

Table 62. PULSE_GEN_CONFIG Bit Descriptions

Bits

Bit Name

Access

Description

PULSE_GEN_1_INV

Read/write

0 = no inversion on Pulse Generator 1. On time is defined as the length of time a high

signal is output.

1 = inverted output on Pulse Generator 1. On time is defined as the length of time a high

signal is output.

PULSE_GEN_1_ON_CLK

Read/write

Defines clock speed for the on time of Pulse Generator 1.

0 = 1 ms.

1 = 125 ms.

Setting PULSE_GEN_1_ON_CLK = 1 and PULSE_GEN_1_PRD_CLK = 0 is not a supported

configuration.

PULSE_GEN_1_PRD_CLK

Read/write

Defines clock speed for the period of Pulse Generator 1.

0 = 1 ms.

1 = 125 ms.

Setting PULSE_GEN_1_ON_CLK = 1 and PULSE_GEN_1_PRD_CLK = 0 is not a supported

configuration.

PULSE_GEN_1_EN

Read/write

0 = Pulse Generator 1 is disabled. The off signal is output constantly.

1= Pulse Generator 1 is enabled.

PULSE_GEN_2_INV

Read/write

0 = no inversion on Pulse Generator 2. On time is defined as the length of time a high

signal is output.

1 = inverted output on Pulse Generator 2. On time is defined as the length of time a low

signal is output.

PULSE_GEN_2_ON_CLK

Read/write

Defines clock speed for the on time of Pulse Generator 2.

0 = 1 ms.

1 = 125 ms.

Setting PULSE_GEN_2_ON_CLK = 1 and PULSE_GEN_2_PRD_CLK = 0 is not a supported

configuration.

PULSE_GEN_2_PRD_CLK

Read/write

Defines clock speed for the period of Pulse Generator 2.

0 = 1 ms.

1 = 125 ms.

Setting PULSE_GEN_2_ON_CLK = 1 and PULSE_GEN_2_PRD_CLK = 0 is not a supported

configuration.

PULSE_GEN_2_EN

Read/write

0 = Pulse Generator 2 is disabled. The off signal is output constantly.

1 = Pulse Generator 2 is enabled.

LOGIC_CFG, Register 0x36

Table 63. LOGIC_CFG Bit Descriptions

Bits

Bit Name

Access

Description

Reserved

Reserved.

LY_INV

Read/write

0 = the LY output is not inverted before passing into the logic block.

1 = inverts the LY output from the logic block.

LC_INV

Read/write

0 = the LC input is not inverted before passing into the logic block.

1 = inverts LC input before passing it into the logic block.

LB_INV

Read/write

0 = the LB input is not inverted before passing into the logic block.

1 = inverts LB input before passing it into the logic block.

LA_INV

Read/write

0 = the LA input is not inverted before passing into the logic block.

1 = inverts LA input before passing it into the logic block.

[2:0]

LOGIC_SEL[2:0]

Read/write

Configures the digital mux for the logic block. Refer to Figure 19.

000 = off/disable.

001 = AND.

010 = OR.

011 = XOR.

100 = FF.

101 = IN_LA.

110 = IN_LB.

111 = IN_LC.

ADP5586ACBZ-00-R7 Datasheet(PDF) 37 Page - Analog Devices

ADP5586ACBZ-00-R7 Datasheet(HTML) 37 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44

Datasheet Descarga

Enlace URL