WM8580 datasheet(49/97 Pages) WOLFSON

49 / 97 page

Production Data

WM8580

PD Rev 4.3 August 2007

The oscillator XOUT pin has one control bit as shown in Table 39.

ADDRESS

BIT

LABEL

DEFAULT

DESCRIPTION

R51

PWRDN 2

33h

OSCPD

Oscillator XOUT Power Down

0 = Power Up XOUT (crystal mode)

1 = Power Down XOUT (CMOS

clock input mode)

Table 39 Oscillator Control

PHASE-LOCKED LOOP (PLL)

The WM8580 has two on-chip phase-locked loop (PLL) circuits which can be used to synthesise two

independent clock signals (PLLACLK and PLLBCLK) from the external oscillator clock. The PLLs can

be used to:

•

Generate clocks necessary for the S/PDIF receiver to lock on to and recover S/PDIF data

from an incoming S/PDIF data stream.

•

Generate clocks which may be used to drive the MCLK and/or CLKOUT pins.

•

Generate clocks which may be used by the S/PDIF transmitter to encode and transmit a

S/PDIF data stream.

•

Generate clocks which may be used as the master clock source for the the ADC and

DACs.

•

Generate clocks which may be used by the master mode clock generator to generate the

BCLK and LRCLK signals for the digital audio interfaces.

The PLLs can be enabled or disabled using the register bits shown in Table 40.

ADDRESS

BIT

LABEL

DEFAULT

DESCRIPTION

PLLAPD

R51

PWRDN 2

33h

PLLBPD

PLL Power Down Control

0 = Power Up PLL

1 = Power Down PLL

Table 40 PLL Power Down Control

The PLLs have two modes of operation:

•

PLL S/PDIF Receive Mode (Selected if S/PDIF Receiver Enabled)

In S/PDIF receive mode, PLLA is automatically controlled by the S/PDIF receiver to allow the

receiver to use PLLA to track and lock on to the incoming S/PDIF data stream. In this case, CLK1 is

automatically maintained at a constant frequency of 256fs relative to the sample rate of the

recovered S/PDIF stream. PLLB must be configured to produce CLK2, a specific reference clock for

the S/PDIF receiver.

PLLACLK may be used as a 256fs or 128fs (selectable – refer to Table 45) master clock source

when in S/PDIF receiver mode. PLLBCLK is not available and must not be selected as the clock

source for any internal function when the S/PDIF receiver is enabled.

If the sample frequency of the incoming stream is changed and PLLA is forced to unlock in order to

track to the new sample frequency, the PLLACLK signal will be stopped until the S/PDIF receiver

has locked to the incoming stream at the new sample frequency. If the incoming S/PDIF stream

stops, the PLLA_ N and PLLA_K values will be frozen and the PLLACLK will continue at the

frequency set by the last recovered S/PDIF stream.

Refer to Table 41 and Table 43 for details of the registers available for configuration in this mode.

Refer to the S/PDIF Receive Mode Clocking section on page 54 for full details.

WM8580 Datasheet(PDF) 49 Page - Wolfson Microelectronics plc

WM8580 Datasheet(HTML) 49 Page - Wolfson Microelectronics plc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97

Datasheet Descarga

Enlace URL