MODEL: TC10EM

TC10EM SPECIFICATIONS

ES-9581 Rev.4 Page 2/7

http://www.m-system.co.jp/

• Bank

• Event input

• CT input

• Auto-tuning

Refer to the instruction manual for detail.

■Recommended solderless terminal

3.3 (.13) max

mm (inch)

MODBUS COMMUNICATION

Communication: Half-duplex, asynchronous, no procedure

Standard: Conforms to TIA/EIA-485-A

Transmission distance: 500 meters max.

Transmission media: Shielded twisted-pair cable

(CPEV-S 0.9 dia.)

Node adress: 1 to 247

Data mode: RTU (Binary)

Parity: None, even or odd

Baud rate: 4800, 9600, 19.2 k, 38.4 k, 57.6 k (bps)

Stop bit: 1 or 2

Node adress, parity, baud rate setting: With front panel

operation buttons or PC configurator software (model:

TC10CFG)

Terminating resistor: Built-in (Enable by shorting between

pin 4 and 5)

DISPLAY

PV display: 5 digits 7-segment green LED, 19.5 mm (.77”)

height

SP display: 5 digits 7-segment red LED, 12.5 mm (.49”)

height, switchable to MV display

Display range: -32000 to 32000

Zero indication: Higher-digit zeros are suppressed.

Loop status indicators

Loop1: Amber LED turns on when loop 1 chosen

Loop2: Amber LED turns on when loop 2 chosen

Bank1: Green LED turns on when bank 1 chosen

Bank2: Green LED turns on when bank 2 chosen

Bank3: Green LED turns on when bank 3 chosen

Bank4: Green LED turns on when bank 4 chosen

Alarm1: Red LED turns on at alarm 1

Alarm2: Red LED turns on at alarm 2

Alarm3: Red LED turns on at alarm 3

Alarm4: Red LED turns on while setting is saving to the

non-volatile memory.

Run: Green LED turns on while loop is in operation.

Man: Green LED turns on during manual mode

Local: Green LED turns on when local SP chosen

At: Green LED turns on during auto-tuning

Out1: Green LED turns on when MV1 output

Out2: Green LED turns on when MV2 output

Engineering unit indication: Sticker label attached

DC, AC, mV, V, kV, μA, mA, A, kA, mW, W,

kW, var, kvar, Mvar, VA, Hz, Ω, kΩ, MΩ,

cm, mm, m, m/sec, mm/min, cm/min, m/min,

N, kN, Pa, kPa, MPa, t, t/h, ℃, °F, %RH, J,

INPUT SPECIFICATIONS

■ Universal input 1, 2 (Pv1, Pv2)

For type and range configuration, refer to the instruction

manual.

DC Current:

Input range: 0 - 20 mA DC

Input resistance: 49.9 Ω resistor incorporated

• DC voltage input

Input resistance: ≥ 10 kΩ (-1000 to +1000 mV DC)

Input resistance: ≥ 1 MΩ (-10 to +10 V DC)

• Thermocouple

Input resistance: ≥ 10 kΩ

Input range: Refer to the table 1

Burnout sensing: ≤ 4 μA

Conformance range: Refer to the table 1

• RTD (2-wire or 3-wire)

Excitation: ≤ 0.33 mA

Input range: Refer to the table 1

Allowable leadwire resistance: 20 Ω per wire

• Resistance

Excitation: ≤ 0.33 mA

Allowable leadwire resistance: 20 Ω per wire

• Potentiometer

Excitation: ≤ 0.33 mA

Input range: 0 to 4000 Ω

Allowable leadwire resistance: 20 Ω per wire

■ Clamp-on current sensor (CT1, CT2)

(Sensor model No.: AC input)

CLSE-R5: 0 – 5 A

CLSE-05: 0 – 50 A

CLSE-10: 0 – 100 A

CLSE-20: 0 – 200 A

CLSE-40: 0 – 400 A

CLSE-60: 0 – 600 A

Frequency: 50 / 60 Hz (45 - 65 Hz)

Max. working voltage: 480 V AC (primary side)

Overload capacity:

CLSE-R5: 10 A continuous, x40 (1 sec.)