MODEL: TC10EM

TC10EM SPECIFICATIONS

ES-9581 Rev.4 Page 3/7

http://www.m-system.co.jp/

CLSE-05: 60 A continuous, x40 (1 sec.)

CLSE-10: 120 A continuous, x40 (1 sec.)

CLSE-20: 240 A continuous, x40 (1 sec.)

CLSE-40: 480 A continuous, x40 (1 sec.)

CLSE-60: 720 A continuous, x40 (1 sec.)

Operational range

CLSE-R5: ≤ 5 A

CLSE-05: ≤ 50 A

CLSE-10: ≤ 100 A

CLSE-20: ≤ 200 A

CLSE-40: ≤ 400 A

CLSE-60: ≤ 600 A

Caution 1: The output values may vary depending on the

accuracy of engagement at the clamp connection.

Caution 2: The sensor’s mechanical construction may cause

it to generate resonance sound. However, it does not affect

the perfomrance of the sensor.

■ Discrete Input (Di1, Di2)

Contact rating: 3.3 V @1 mA

Detection levels:

≤ 15 kΩ / 0.5 V at close

≥ 350 kΩ / 2.5 V at open

OUTPUT SPECIFICATIONS

Four control outputs are configurable to Mv, Ao or Do.

■ Control Output (Mv1, Mv2)

Specify one type of output with the code number from 3

types shown below.

• DC Current: 0 – 20 mA DC

Operational range: 0 – 23 mA DC

Load resistance: ≤ 500 Ω

• DC Voltage: 0 – 10 V DC

Operational range: 0 - 11.5 V DC

Load resistance: ≥ 2 kΩ

• 12 V Voltage pulse

Maximum frequency: 1 Hz

Minimum pulse width: 1 msec.

Hi level: 12 V ±15 %

Lo level: ≤ 0.5 V

Load resistance: 600 Ω min.

■ Control Output (Do1, Do2)

• Open collector

Maximum frequency: 1 Hz

Minimum pulse width: 1 msec.

Output rating: 50 V DC 100 mA (resistive load)

Saturation voltage: 0.5 V DC

INSTALLATION

Power Consumption

•AC:

Approx. 6 VA at 100 V

Approx. 7 VA at 200 V

Approx. 8 VA at 240 V

Operating temperature: -10 to +55°C (14 to 131°F)

Operating humidity: 5 to 90 %RH (non-condensing)

Atmosphere: No corrosive gas or heavy dust

Mounting: Panel flush mounting

Weight: 450 g (0.99 lb)

PERFORMANCE in percentage of span

Accuracy

• Pv1 or Pv2: Refer to "Input type, range & conversion

accuracy" section.

• CT1 or CT2: ±2 % (sensor error margin not included)

• Mv1 or Mv2: ±0.5 %

Cold junction compensation error (thermocouple input):

±2.0°C at 0 – 50°C (±3.6°F at 32 – 122°F)

CJC sensor is adjacently attached to the input terminals.

CJC is available for each universal input 1 and 2.

Temp. coefficient

• Pv1 or Pv2: ±0.03 %/°C (± 0.02 %/°F)

• CT1 or CT2: ±0.03 %/°C (± 0.02 %/°F)

Response time

• CT1 or CT2: ≤ 2 sec. (0 – 90 %)

• Mv1 or Mv2: ≤ 1 sec. (0 – 90 %, DC output)

Burnout response (thermocouple, RTD input): ≤ 10 s

Insulation resistance: ≥ 100 MΩ with 500 V DC

Dielectric strength: 2000 V AC @1 minute (Pv1 to Pv2 to

CT1 or CT2 to Di1 or Di2 to MV1 or MV2 to Do1 or Do2 to

Modbus to power to ground)

STANDARDS & APPROVALS

EU conformity:

EMC Directive

EMI EN 61000-6-4

EMS EN 61000-6-2

Low Voltage Directive

EN 61010-1

Installation Category II

Pollution Degree 2

Input to output to power – Reinforced insulation (300 V)

Input or output or power to Modbus – Basic insulation (300

V)

RoHS Directive

EN 50581