TL072CD datasheet(11/75 Pages) TI

11 / 75 page

6 Specifications

6.1 Absolute Maximum Ratings: TL07xH

over operating ambient temperature range (unless otherwise noted) (1)

MIN

MAX

UNIT

Supply voltage, VS = (VCC+) – (VCC–)

Signal input pins

Common-mode voltage (3)

(VCC–) – 0.5

(VCC+) + 0.5

Differential voltage (3)

VS + 0.2

Current (3)

–10

Output short-circuit (2)

Continuous

Operating ambient temperature, TA

–55

150

°C

Junction temperature, TJ

150

°C

Storage temperature, Tstg

–65

150

°C

(1)

Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress

ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under

Recommended Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device

reliability.

(2)

Short-circuit to ground, one amplifier per package.

(3)

Input pins are diode-clamped to the power-supply rails. Input signals that may swing more than 0.5 V beyond the supply rails must be

current limited to 10 mA or less.

6.2 Absolute Maximum Ratings: All Devices Except TL07xH

over operating free-air temperature range (unless otherwise noted) (1)

MIN

MAX

UNIT

VCC+ - VCC– Supply voltage

–0.3

Input voltage (3)

VCC– – 0.3

VCC– + 36

IIK

Input clamp current

–50

Duration of output short circuit(2)

Unlimited

Operating virtual junction temperature

150

°C

Case temperature for 60 seconds - FK package

260

°C

Lead temperature 1.8 mm (1/16 inch) from case for 10 seconds

300

°C

Tstg

Storage temperature

–65

150

°C

(1)

Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings

only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating

Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

(2)

The output may be shorted to ground or to either supply. Temperature and supply voltages must be limited to ensure that the

dissipation rating is not exceeded.

(3)

Differential voltage only limited by input voltage.

6.3 ESD Ratings: TL07xH

VALUE

UNIT

V(ESD)

Electrostatic discharge

Human body model (HBM), per ANSI/ESDA/JEDEC JS-001(1)

±1500

Charged device model (CDM), per JEDEC specification JESD22-C101 (2)

±1000

(1)

JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.

(2)

JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.

www.ti.com

TL071, TL071H, TL071A, TL071B

TL072, TL072H, TL072A, TL072B

TL074, TL074H, TL074A, TL074B, TL072M, TL074M

SLOS080Q – SEPTEMBER 1978 – REVISED JUNE 2021

Submit Document Feedback

Product Folder Links: TL071 TL071H TL071A TL071B TL072 TL072H TL072A TL072B TL074 TL074H TL074A

TL074B TL072M TL074M

TL072CD Datasheet(PDF) 11 Page - Texas Instruments

TL072CD Datasheet(HTML) 11 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75

Datasheet Descarga

Enlace URL