STM32G474PBY3TR datasheet(130/236 Pages) STMICROELECTRONICS

130 / 236 page

Electrical characteristics

STM32G474xB STM32G474xC STM32G474xE

130/236

DS12288 Rev 5

All I/Os are CMOS- and TTL-compliant (no software configuration required). Their

characteristics cover more than the strict CMOS-technology or TTL parameters. The

coverage of these requirements is shown in Figure 25 for standard I/Os, and in Figure 25 for

5 V tolerant I/Os.

Figure 25. I/O input characteristics

Output driving current

The GPIOs (general purpose input/outputs) can sink or source up to ±8 mA, and sink or

source up to ± 20 mA (with a relaxed VOL/VOH).

In the user application, the number of I/O pins which can drive current must be limited to

respect the absolute maximum rating specified in Section 5.2:

•

The sum of the currents sourced by all the I/Os on VDD, plus the maximum

consumption of the MCU sourced on VDD, cannot exceed the absolute maximum rating

ΣIVDD (see Table 14: Voltage characteristics).

•

The sum of the currents sunk by all the I/Os on VSS, plus the maximum consumption of

the MCU sunk on VSS, cannot exceed the absolute maximum rating ΣIVSS (see

Table 14: Voltage characteristics).

2. Data based on characterization results, not tested in production

3. Guaranteed by design.

4. This value represents the pad leakage of the I/O itself. The total product pad leakage is provided by this formula:

ITotal_Ileak_max = 10 μA + [number of I/Os where VIN is applied on the pad] ₓ Ilkg(Max).

5. Pull-up and pull-down resistors are designed with a true resistance in series with a switchable PMOS/NMOS. This

PMOS/NMOS contribution to the series resistance is minimal (~10% order).

MSv37613V1

Teste

d in

production

CMOS

requirement

Vih

min

= 0

.7xV

DDIO

Based

on simulati

on Vi

h min

= 0.6

1xVDDIOx

+0.05

for 1.08<V

DDIOx

<1.62

or 0.49xV

DDIOx

+0.2

6 for

VDDI

Ox>1

.62

Based

on simu

lation

Vil m

ax =0.43xV

DDIOx

-0.1 for

1.08

<VDDIOx

<1.62

or 0.39xV

DDIOx

-0.06

for VDDIO

x>1.62

Tested

in produ

ction CMOS

requirement

Vil ma

x = 0.3xVdd

TTL requirement Vih min = 2V

TTL requirement Vil max = 0.8V

STM32G474PBY3TR Datasheet(PDF) 130 Page - STMicroelectronics

STM32G474PBY3TR Datasheet(HTML) 130 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Descarga

Enlace URL