STM32L100RB datasheet(55/103 Pages) STMICROELECTRONICS

55 / 103 page

DocID024295 Rev 5

55/103

STM32L100C6 STM32L100R8/RB

Electrical characteristics

IDD (WU

from Stop)

RMS (root

mean square)

supply current

during wakeup

time when

exiting from

Stop mode

MSI = 4.2 MHz

VDD = 3.0 V

TA = -40°C to 25°C

MSI = 1.05 MHz

1.45

MSI = 65 kHz(6)

1.45

1. The typical values are given for VDD = 3.0 V and max values are given for VDD = 3.6 V, unless otherwise

specified.

2. Guaranteed by characterization results, unless otherwise specified.

3. LCD enabled with external VLCD, static duty, division ratio = 256, all pixels active, no LCD connected.

4. LCD enabled with external VLCD, 1/8 duty, 1/3 bias, division ratio = 64, all pixels active, no LCD

connected.

5. Based on characterization done with a 32.768 kHz crystal (MC306-G-06Q-32.768, manufacturer JFVNY)

with two 6.8pF loading capacitors.

6. When MSI = 64 kHz, the RMS current is measured over the first 15 µs following the wakeup event. For the

remaining time of the wakeup period, the current is similar to the Run mode current.

Table 21. Typical and maximum current consumptions in Stop mode (continued)

Symbol

Parameter

Conditions

Typ

(1)

Max

(1)(2)

Unit

Table 22. Typical and maximum current consumptions in Standby mode

Symbol

Parameter

Conditions

Typ(1)

Max

(1)(2)

Unit

IDD

(Standby

with RTC)

Supply current in Standby

mode with RTC enabled

RTC clocked by LSI (no

independent watchdog)

TA = -40 °C to 25 °C

VDD = 1.8 V

0.9

µA

TA = -40 °C to 25 °C

1.1

1.8

TA = 55 °C

1.42

2.5

TA= 85 °C

1.87

RTC clocked by LSE (no

independent watchdog)(3)

TA = -40 °C to 25 °C

VDD = 1.8 V

TA = -40 °C to 25 °C

1.33

2.9

TA = 55 °C

1.59

3.4

TA= 85 °C

2.01

4.3

IDD

(Standby)

Supply current in Standby

mode with RTC disabled

Independent watchdog

and LSI enabled

TA = -40 °C to 25 °C

1.1

1.6

Independent watchdog

and LSI OFF

TA = -40 °C to 25 °C

0.3

0.55

TA = 55 °C

0.5

0.8

TA = 85 °C

1.7

IDD (WU

from

Standby)

RMS supply current during

wakeup time when exiting

from Standby mode

VDD = 3.0 V

TA = -40 °C to 25 °C

1. The typical values are given for VDD = 3.0 V and max values are given for VDD = 3.6 V, unless otherwise specified.

2. Guaranteed by characterization results, unless otherwise specified.

3. Based on characterization done with a 32.768 kHz crystal (MC306-G-06Q-32.768, manufacturer JFVNY) with two 6.8pF

loading capacitors.

STM32L100RB Datasheet(PDF) 55 Page - STMicroelectronics

STM32L100RB Datasheet(HTML) 55 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Descarga

Enlace URL