PC87373 datasheet(100/174 Pages) NSC

100 / 174 page

6.0 System Wake-Up Control (SWC) (Continued)

100

www.national.com

Revision 1.1

6.4.6

General-Purpose Status 1 Register 2 (GPE1_STS_2)

This register contains “child” events 16-23 of the GPE1_STS register.

The status bits behave according to the Sticky status bit definition in the ACPI Specification (i.e., the bit is set when the level

of the hardware signal is high and is only cleared by the software writing 1 to it).

Power Well: VSB3

Location:

Offset 0Ah

Type:

R/W1C

Bit

76543210

Name

KBD_EVT3

_STS

KBD_EVT2

_STS

KBD_EVT1

_STS

MS_EVT

_STS

KBD_ANYK

_STS

RI1_EVT

_STS

RI2_EVT

_STS

Reserved

Reset

00000000

Bit

Description

KBD_EVT3_STS (Keyboard Event 3 Status). Indicates that “PM Key 3” was pressed and that the event was

identiﬁed by the Keyboard/Mouse Wake-Up Detector. This bit is set only if the Keyboard/Mouse Wake-Up

Detector is in Power Management Keys mode (see Section 6.3.7 on page 94). Writing 1 clears this bit; writing 0

is ignored.

0: Inactive since last cleared (default)

1: The “PM Key 3” key was pressed on the keyboard

KBD_EVT2_STS (Keyboard Event 2 Status). Indicates that “PM Key 2” was pressed and that the event was

identiﬁed by the Keyboard/Mouse Wake-Up Detector. This bit is set only if the Keyboard/Mouse Wake-Up

Detector is in Power Management Keys mode (see Section 6.3.7 on page 94). Writing 1 clears this bit; writing 0

is ignored.

0: Inactive since last cleared (default)

1: The “PM Key 2” key was pressed on the keyboard

KBD_EVT1_STS (Keyboard Event 1 Status). This bit indicates that a keyboard event occurred and was

identiﬁed by the Keyboard/Mouse Wake-Up Detector. The event type depends on the selected operation mode

for the Keyboard/Mouse Wake-Up Detector (see Sections 6.3.7 and 6.3.8 on page 94.):

Pressing any key or a sequence of special keys in Special Key Sequence mode

Pressing a sequence of keys in Password mode

Pressing the “PM Key 1” in Power Management Keys mode

Writing 1 clears this bit; writing 0 is ignored.

0: Inactive since last cleared (default)

1: A keyboard event occurred

MS_EVT_STS (Mouse Event Status). Indicates that a mouse event occurred and was identiﬁed by the

Keyboard/Mouse Wake-Up Detector (see Section 6.3.8 on page 95). Writing 1 clears this bit; writing 0 is ignored.

0: Inactive since last cleared (default)

1: A mouse event occurred

KBD_ANYK_STS (Keyboard Any-Key Status). This bit indicates that any key was pressed and that the event

was identiﬁed by the Keyboard/Mouse Wake-Up Detector. This bit is set only if the Keyboard/Mouse Wake-Up

Detector is in Fast Any-Key mode (see Section 6.3.7 on page 94). Writing 1 clears this bit; writing 0 is ignored.

0: Inactive since last cleared (default)

1: A keyboard event occurred

RI1_EVT_STS (RI1 Event Status). Indicates that a telephone ring signal was received at Serial Port 1 and the

event was identiﬁed by the RI Wake-Up Detector. This bit is set by a high-to-low transition at the RI1 pin (see

Section 6.2.1 on page 81). Writing 1 clears this bit; writing 0 is ignored.

0: Inactive since last cleared (default)

1: A telephone ring signal was received at Serial Port 1

PC87373 Datasheet(PDF) 100 Page - National Semiconductor (TI)

PC87373 Datasheet(HTML) 100 Page - National Semiconductor (TI)

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Descarga

Enlace URL