| Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
RT9481 Datasheet(PDF) 21 Page - Richtek Technology Corporation |
|
|
|||||||||||||||||||||||||||||
RT9481 Datasheet(HTML) 21 Page - Richtek Technology Corporation |
|
21 / 41 page ![]() RT9481 Copyright © 2015 Richtek Technology Corporation. All rights reserved. is a registered trademark of Richtek Technology Corporation. DS9481-00 June 2015 www.richtek.com 21 ADC Conversion Operation Flow Figure 4 shows ADC conversion operation flow. ADC conversion starts from set ADC channel CH_SEL (ADC_CLT[7:5]) and set ADC_START (ADC_CLT[0]) to high. ADC conversion time is 25ms and ADC_DONEI (MISC_IRQ[7]) will set to high and ADC_STAT (MISC_STAT1) will set to low also, the host could read them to make sure ADC conversion completes. The host could read ADC code high byte (ADC_CODEH[7:0]) and low byte (ADC_CODEL[7:0]) to calculate the voltage or current measurement relative to ADC channel. Table 9 shows the every measurement equation of ADC channel. Please pay attention to the calculation of IRS, it need to consider the setting of ICHG (CHG_CTRL6[7:4]). ADC code format is unsigned. If operation is Charger mode, IVRS means battery charging current. If operation is boost mode, IRS means battery discharging current. The code of IRS is invalid if SWITCHING_EN (CHG_STA1[0]) is set to low. And the code of IUSBOUT is invalid if EN_LDSW (USBOUT_CTL[6]) is set to low. The TS pin will automatic output 35uA during ADC TS channel under conversion. It will cause the IR drop on NTC thermistor and then ADC measure the voltage on TS pin. The host could get the temperature by mapping the voltage. We suggest to use 10k NTC which the beta (B25/85) is 3435k, like SEMITEC 103AT. Table 9. Calculate Voltage or Current Measurement ADC Channel Measurement Equation Measurement Range VBAT VBAT = ( ( ADC_CODEH x 256 ) + ADC_CODEL ) x 1.25 mV 0V to VDDA VBUS VBUS = ( ( ADC_CODEH x 256 ) + ADC_CODEL ) x 6.25 mV 1V to 18V USBOUT USBOUT = ( ( ADC_CODEH x 256 ) + ADC_CODEL ) x 6.25 mV 1V to 6V TS TS = ( ( ADC_CODEH x 256 ) + ADC_CODEL ) x 1.25 mV 0V to VDDA IRS IRS = ( ( ADC_CODEH x 256 ) + ADC_CODEL ) x ICHG x 1.25 mA 0A to 6A IUSBOUT IUSBOUT = ( ( ADC_CODEH x 256 ) + ADC_CODEL ) x 2.5 mA 0A to 6A |
|
Enlace URL |
| ¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Enlace a la hoja de datos | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |