HCPL3100 datasheet(6/10 Pages) HP

6 / 10 page

1-343

Switching Specifications (T

A = 25°C)

Parameter

Sym.

Device

Min.

Typ.

Max. Units

Test Conditions

Fig.

Note

Propagation

PLH

HCPL-3100

µsI

F = 10 mA

CC = 24 V,

2, 6

Delay Time to

VO1 = 24 V,

25,

High Output

HCPL-3101

0.3

0.5

µsI

F = 5 mA

G = 47 Ω,

26,

Level

G = 3000 pF

Propagation

PHL

HCPL-3100

µsI

F = 10 mA

Delay Time to

Low Output

HCPL-3101

0.3

0.5

µsI

F = 5 mA

Level

Rise Time

HCPL-3100

0.2

0.5

µsI

F = 10 mA

HCPL-3101

F = 5 mA

Fall Time

HCPL-3100

0.2

0.5

µsI

F = 10 mA

HCPL-3101

IF = 5 mA

Output High

|CM

HCPL-3100

1500

5000

µsI

F = 10 mA

CM = 600 V

Level Common

(peak),

Mode Transient

HCPL-3101

F = 5mA

CC = 24 V

Immunity

O1 = 24 V

∆V

02H = ∆V02L

Output Low

|CM

1500

5000

µsI

F = 0 mA

= 2.0 V

Level Common

Mode Transient

Immunity

Notes:

1. Derate absolute maximum ratings with ambient temperatures as shown in Figures 11 and 12.

2. A bypass capacitor of 0.01

µF or more is needed near the device between V

CC and GND when measuring output and transfer

characteristics.

3. IFLH represents the forward current when the output goes from low to high.

4. Device considered a two terminal device; pins 1-4 are shorted together and pins 5-8 are shorted together.

5. For devices with minimum VISO specified at 5000 V rms, in accordance with UL 1577, each optocoupler is proof-tested by applying an

insulation test voltage

≥ 6000 V rms for one second (leakage current detection limit, I

I-O ≤ 200 µA).

6. The tPLH and tPHL propagation delays are measured from the 50% level of the input pulse to the 50% level of the output pulse.

7. R2 limits the Q1 and Q2 peak currents. For more applications and circuit design information see Application Note “Power Transistor

Gate/Base Drive Optocouplers.”

Packaging Characteristics

Parameter

Sym.

Min.

Typ.

Max.

Units

Test Conditions

Fig.

Note

Input-Output Momentary

ISO

5000

V rms

RH = 40% to 60%

4, 5

Withstand Voltage*

t = 1 min, TA = 25°C

Resistance (Input-Output)

RI-O

5x1010

1011

–

Ω

VI-O = 500 V, TA = 25°C4

RH = 40% to 60%

Capacitance (Input-Output)

I-O

–

1.2

–

f = 1 MHz

*The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output

continuous voltage rating. For the continuous voltage rating refer to the VDE 0884 Insulation Characteristics Table (if applicable), your

equipment level safety specification, or HP Application Note 1074, “Optocoupler Input-Output Endurance Voltage.”

HCPL3100 Datasheet(PDF) 6 Page - Agilent(Hewlett-Packard)

HCPL3100 Datasheet(HTML) 6 Page - Agilent(Hewlett-Packard)

Html Pages

1 2 3 4 5 6 7 8 9 10

Datasheet Descarga

Enlace URL