| Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
dsPIC33FJ64GS406 Datasheet(PDF) 417 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
dsPIC33FJ64GS406 Datasheet(HTML) 417 Page - Microchip Technology |
|
417 / 456 page ![]() 2009-2012 Microchip Technology Inc. DS70591E-page 417 dsPIC33FJ32GS406/606/608/610 and dsPIC33FJ64GS406/606/608/610 28.2 AC Characteristics and Timing Parameters This section defines the dsPIC33FJ32GS406/606/608/610 and dsPIC33FJ64GS406/606/608/610 AC characteristics and timing parameters for 50 MIPS devices. TABLE 28-5: EXTERNAL CLOCK TIMING REQUIREMENTS AC CHARACTERISTICS Standard Operating Conditions: 3.0V to 3.6V (unless otherwise stated) Operating temperature -40°C TA +85°C for Industrial Param No. Symb Characteristic Min Typ(1) Max Units Conditions MOS10 FIN External CLKI Frequency (External clocks allowed only in EC and ECPLL modes) DC — 50 MHz EC Oscillator Crystal Frequency 3.5 — 10 — — — 10 33 50 MHz kHz MHz XT SOSC HS MOS20 TOSC TOSC = 1/FOSC 10 — DC ns MOS25 TCY Instruction Cycle Time(2) 20 — DC ns MOS30 TosL, TosH External Clock in (OSC1) High or Low Time 0.375 x TOSC — 0.625 x TOSC ns EC MOS31 TosR, TosF External Clock in (OSC1) Rise or Fall Time —— 20 ns EC MOS40 TckR CLKO Rise Time(3) —5.2 — ns MOS41 TckF CLKO Fall Time(3) —5.2 — ns MOS41 GM External Oscillator Transconductance 14 16 18 mA/V VDD = 3.3V, TA = +25ºC Note 1: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated. 2: Instruction cycle period (TCY) equals two times the input oscillator time base period. All specified values are based on characterization data for that particular oscillator type under standard operating conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation and/or higher than expected current consumption. All devices are tested to operate at “min.” values with an external clock applied to the OSC1/CLKI pin. When an external clock input is used, the “max.” cycle time limit is “DC” (no clock) for all devices. 3: Measurements are taken in EC mode. The CLKO signal is measured on the OSC2 pin. |
|
Enlace URL |
| ¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Enlace a la hoja de datos | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |