 |
Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
|
Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
WM8860 Datasheet(PDF) 86 Page - Wolfson Microelectronics plc |
|
|
|||||||||||||||||||||||||||||
WM8860 Datasheet(HTML) 86 Page - Wolfson Microelectronics plc |
|
|
86 / 184 page  WM8860 Pre-Production w PP, April 2011, Rev 3.2 86 PROCESSING STATE VERB Verb ID Payload [7:0] Response[31:0] Get F03h 00h Bits [31:0] in the table below Set 703h Bits [7:0] in the table below 00000000h Bit Bitfield Name RW Default Description [31:8] Rsvd R 000000h Reserved [7:0] Processing State RW 01h The processing node is the high-pass filter (HPF). The processing state is controlled as follows: 00h = Processing Off: HPF disabled 01h = Processing On: HPF enabled 02h = Processing Off: HPF disabled (benign not supported) 03h-7Fh = Reserved 80h-FFh = Vendor Specific – not used POWER STATE VERB Verb ID Payload [7:0] Response[31:0] Get F05h 00h Bits [31:0] in the table below Set 705h Bits [7:0] in the table below 00000000h Bit Bitfield Name RW Default Description [31:8] Rsvd R 000000h Reserved [7:4] PS-Act R 3h Indicates the actual power state of the MIC1 widget node: 0h = D0 1h = D1 2h = D2 3h = D3 The power state of the MIC1 widget is controlled by PS-Set below, however the control may be superseded by the PS-Set of the AFG node. [3:0] PS-Set RW 3h Sets the power state of the MIC1 widget node: 0h = D0 1h = D1 2h = D2 3h = D3 CONVERTER STREAM, CHANNEL VERB Verb ID Payload [7:0] Response[31:0] Get F06h 00h Bits [31:0] in the table below Set 706h Bits [7:0] in the table below 00000000h Bit Bitfield Name RW Default Description [31:8] Rsvd R 000000h Reserved [7:4] Stream RW 0h Stream ID used by this widget. Note that Stream ID = 0h is used to indicate an unused stream, and converters will not transfer/receive link data for streams with an ID of 0h. For multi-channel capture on MIC1 and MIC2, the Stream value should be the same for both. [3:0] Channel RW 0h Lowest channel number used by this widget. Note: When MIC1 and MIC2 are setup for multi-channel capture, only a setting of 0h and 2h are applicable. However, the values are mutually exclusive, in that if Channel has been set to 0h for the MIC1 node, it must be set to 2h for the MIC2 node. Both nodes should have Channel set to 0h |
|
Enlace URL |
| ¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Enlace a la hoja de datos | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Spanish ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
