F1206A0R20FSTR datasheet(20/23 Pages) AVX

20 / 23 page

Accu-Guard®

SMD Thin-Film Fuse

Thus, for current pulse in Figure 3b, the Joule integral is:

{(0.56A)2+0.56A x (1A-0.56A)+

[(1A-0.56A)2]} x 3 x 10-3s = 1.9 x 10-3A2sec.

Fig. 3a. Trapezoidal pulse parameters for Joule

integral calculation, example #3.

4. Lightning strike

A lightning strike pulse is shown in Figure 4a. After an initial

linear rise, the current declines exponentially.

3. Trapezoidal current pulse

The Joule integral for a trapezoidal pulse is

[(Imin.)2 + Imin. x (Imax. - Imin.) + (Imax-Imin)2] x t,

see Fig. 3a.

l min.

l max.

0.5 msec/div

0.5A/div

Fig. 3b. Trapezoidal pulse, example #3.

According to the I2t graph on page 6, the 0.5A fuse should

be chosen for this application, see Figure 3c.

FUSE PRE-ARCING JOULE INTEGRALS

vs. PRE-ARCING TIME

0.50A

PRE-ARCING TIME l2t, A2 sec

PRE-ARCING TIME, sec

100

10-1

10-2

10-3

10-4

10-5

10-7

10-6

10-5

10-4

10-3

10-2

10-1

110

Fig. 3c. Choice of 0.5A fuse, example #3.

Pre-arcing I2t

Maximum I2t design rule

I2t for sample switch-on pulse

DESIGNING FOR CURRENT PULSE SITUATIONS (CONT.)

Joule integral for the linear current rise is calculated as for a

triangular pulse, see example #2.

The Joule integral for the exponential decline is

max.

2 x t

0.5 x (-1/2In 0.5) = 0.72Imax.2 x t0.5

Thus, for the sample lightning strike pulse in Figure 4b, the

total Joule integral is:

(25A)2 x 2 x 10-6sec/3+0.72 x (25A)2 x 10 x 10-6sec = 4.92 x 10-3A2sec.

t0.5

0.51 max.

l max.

Fig. 4a. Lightning pulse parameters for Joule

integral calculation, example #4.

μsec/div

5A/div

Fig. 4b. Lightning strike pulse, example #4.

For practical calculations, the duration of exponential decline

may be assumed to be 3t

0.5, because within this time 98.5%

of the pulse energy is released. Thus, the total pulse duration

in this example is 30 μsec, and the 1.25A fuse should be

chosen for this application, see Figure 4c.

FUSE PRE-ARCING JOULE INTEGRALS

vs. PRE-ARCING TIME

Fig. 4c. Choice of 0.5A fuse, example #4.

Pre-arcing I2t

Maximum I2t design rule

I2t for sample switch-on pulse

1.25A

PRE-ARCING TIME l2t, A2 sec

PRE-ARCING TIME, sec

100

10-1

10-2

10-3

10-4

10-5

10-7

10-6

10-5

10-4

10-3

10-2

10-1

110

F1206A0R20FSTR Datasheet(PDF) 20 Page - AVX Corporation

F1206A0R20FSTR Datasheet(HTML) 20 Page - AVX Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23

Datasheet Descarga

Enlace URL