| Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
34825 Datasheet(PDF) 13 Page - Freescale Semiconductor, Inc |
|
|
|||||||||||||||||||||||||||||
34825 Datasheet(HTML) 13 Page - Freescale Semiconductor, Inc |
|
13 / 39 page ![]() Analog Integrated Circuit Device Data Freescale Semiconductor 13 34825 FUNCTIONAL DESCRIPTION INTRODUCTION FUNCTIONAL DESCRIPTION INTRODUCTION The 34825 is designed to support cell phones that adopt the micro or mini-USB connector as the sole wired interface between the cell phone and external accessories. Using the micro-USB connector for charging and USB data communication is required by the OMTP standard for the UCS. The 34825 further extends the micro-USB connector to support other accessories to eliminate all other mechanical connectors in a cell phone. The supported accessories include various audio headsets, UART connection, R/D test cables for firmware downloading, and other user defined accessories, in addition to the chargers defined in the Battery Charging Specification, Revision 1.0, from the USB Implementer’s Forum and the CEA-936-A USB Carkit Specification, from the Consumer Electronics Association (CEA). The supported chargers are listed in Table 7. The 34825 offers two mechanisms to assist the identification of the accessory. The ID detection mechanism allows the cell phone to measure the ID resistor value between the ID pin and the ground with a 5-bit ADC. The VBUS detection mechanism allows the cell phone to find out the connection status between the D+ and D- pins. Together, the exact accessory can be determined. A detection flow is initiated by a change in the VBUS pin voltage or by a change in the ID pin floating status. Detaching the accessory from the micro or mini-USB connector causes the VBUS voltage or/ and the ID resistance to change. The identification flow will be initiated to confirm if an accessory is still connected. The host can also initiate the identification flow by resetting an ACTIVE bit in the register from 1 to 0. Upon the completion of the identification flow, an interrupt signal is sent to the host IC, so the host IC can take further actions. The 34825 contains switches that the host IC can control via an I2C interface. Based on the accessory, the host IC can configure the switch connections in the 34825, so that the signal paths for the USB communication, or the UART communication, or audio accessories can be established between the micro or mini-USB connector pins and the system ICs. If the accessory is a power supply, the supplied voltage is switched to the Li-ion battery charging function in the cell phone via an internal power MOSFET. The host IC controls the 34825 via the I2C serial bus. The register map in the 34825 contains status information of the device and the control bits that the host IC can access to control the 34825. FUNCTIONAL PIN DESCRIPTION SPEAKER RIGHT CHANNEL (SPK_R) Right channel of the baseband speaker output. SPEAKER LEFT CHANNEL (SPK_L) Left channel of the baseband speaker output. MICROPHONE OUTPUT (MIC) Microphone output to the baseband. D+ OF THE USB TRANSCEIVER (D+) D+ line of the USB transceiver. D- OF THE USB TRANSCEIVER (D-) D- line of the USB transceiver. UART RECEIVER (RXD) Receiver line of the UART. UART TRANSMITTER (TXD) Transmitter line of the UART. TEST2 INDICATOR (TEST2) Push-pull output to indicate the type of the connected test cable. IO POWER SUPPLY (VDDIO) Power supply input for the logic IO interface. Generally the IO power supply voltage should be the same as the IO voltage used in the cell phone system. VDDIO is also one of the hardware reset input sources. A falling edge at this pin will reset the 34825. See Reset for more information. TEST1 INDICATOR (TEST1) Open-drain output to indicate the attachment of a test cable. POWER SUPPLY (VDD) Power supply input. Bypass to ground with a 1.0 μF capacitor. INTERRUPT OUTPUT (INT) Active low open-drain output. The INT pin sends an interrupt signal to the host IC when an interrupt event happens. The INT output returns to high voltage once all interrupt bits are read. DATA LINE OF THE I2C INTERFACE (I2C_SDA) Data line of the I2C interface. |
|
Enlace URL |
| ¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Enlace a la hoja de datos | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |