25LC640-ISLASHST datasheet(7/24 Pages) MICROCHIP

7 / 24 page

DS21223H-page 7

25AA640/25LC640

3.0

FUNCTIONAL DESCRIPTION

3.1

Principles Of Operation

The 25XX640 is a 8192 byte Serial EEPROM designed

to interface directly with the Serial Peripheral Interface

(SPI) port of many of today’s popular microcontroller

families, including Microchip’s PIC16C6X/7X micro-

controllers. It may also interface with microcontrollers

that do not have a built-in SPI port by using discrete

I/O lines programmed properly with the software.

The 25XX640 contains an 8-bit instruction register. The

device is accessed via the SI pin, with data being

clocked in on the rising edge of SCK. The CS pin must

be low and the HOLD pin must be high for the entire

operation.

Table 3-1 contains a list of the possible instruction

bytes and format for device operation. All instructions,

addresses, and data are transferred MSB first, LSB

last.

Data is sampled on the first rising edge of SCK after CS

goes low. If the clock line is shared with other

peripheral devices on the SPI bus, the user can assert

the HOLD input and place the 25XX640 in ‘HOLD’

mode. After releasing the HOLD pin, operation will

resume from the point when the HOLD was asserted.

3.2

Read Sequence

The device is selected by pulling CS low. The 8-bit

READ

instruction is transmitted to the 25XX640 fol-

lowed by the 16-bit address with the three MSBs of the

address being “don’t care” bits. After the correct READ

instruction and address are sent, the data stored in the

memory at the selected address is shifted out on the

SO pin. The data stored in the memory at the next

address can be read sequentially by continuing to pro-

vide clock pulses. The internal Address Pointer is auto-

matically incremented to the next higher address after

each byte of data is shifted out. When the highest

address is reached (1FFFh), the address counter rolls

over to address 0000h allowing the read cycle to be

continued indefinitely. The read operation is terminated

by raising the CS pin (Figure 3-1).

3.3

Write Sequence

Prior to any attempt to write data to the 25XX640 array

or STATUS register, the write enable latch must be set

by issuing the WREN instruction (Figure 3-4). This is

done by setting CS low and then clocking out the

proper instruction into the 25XX640. After all eight bits

of the instruction are transmitted, the CS must be

brought high to set the write enable latch. If the write

operation is initiated immediately after the WREN

instruction without CS being brought high, the data will

not be written to the array because the write enable

latch will not have been properly set.

Once the write enable latch is set, the user may

proceed by setting the CS low, issuing a WRITE

instruction, followed by the address, and then the data

to be written. Up to 32 bytes of data can be sent to the

25XX640 before a write cycle is necessary. The only

restriction is that all of the bytes must reside in the

same page. A page address begins with XXX0 0000

and ends with XXX1

1111

. If the internal address

counter reaches XXX1 1111 and the clock continues,

the counter will roll back to the first address of the page

and overwrite any data in the page that may have been

written.

For the data to be actually written to the array, the CS

must be brought high after the Least Significant bit (D0)

of the nth data byte has been clocked in. If CS is

brought high at any other time, the write operation will

not be completed. Refer to Figure 3-2 and Figure 3-3

for more detailed illustrations on the byte write

sequence and the page write sequence, respectively.

While the write is in progress, the STATUS register may

be read to check the status of the WPEN, WIP, WEL,

BP1, and BP0 bits (Figure 3-6). A read attempt of a

memory array location will not be possible during a

write cycle. When the write cycle is completed, the

write enable latch is reset.

TABLE 3-1:

INSTRUCTION SET

Instruction Name

Instruction Format

Description

READ

0000 0011

Read data from memory array beginning at selected address

WRITE

0000 0010

Write data to memory array beginning at selected address

WREN

0000 0110

Set the write enable latch (enable write operations)

WRDI

0000 0100

Reset the write enable latch (disable write operations)

RDSR

0000 0101

Read STATUS register

WRSR

0000 0001

Write STATUS register

25LC640-I/ST Datasheet(PDF) 7 Page - Microchip Technology

25LC640-I/ST Datasheet(HTML) 7 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

Datasheet Descarga

Enlace URL