MSP430x11x

MIXED SIGNAL MICROCONTROLLERS

SLAS196D− DECEMBER 1998 − REVISED SEPTEMBER 2004

17

POST OFFICE BOX 655303

electrical characteristics over recommended ranges of supply voltage and operating free-air

temperature (unless otherwise noted) (continued)

wake-up from lower power modes (LPMx)

PARAMETER

TEST CONDITIONS

MIN

NOM

MAX

UNIT

t(LPM0)/

t(LPM2)

Delay time

VCC = 3 V/5 V

100

ns

t(LPM3)

Delay time

RSel = 4, DCO = 3, MOD = 0

VCC = 3 V/5 V

2.6

6

µs

t(LPM4)

RSel = 4, DCO = 3, MOD = 0

VCC = 3 V/5 V

2.8

6

µs

RAM

PARAMETER

MIN

NOM

MAX

UNIT

V(RAMh)

CPU halted (see Note 1)

1.8

V

NOTE 1: This parameter defines the minimum supply voltage VCC when the data in the program memory RAM remains unchanged. No program

execution should happen during this supply voltage condition.

DCO (MSP430P112)

PARAMETER

TEST CONDITIONS

MIN

NOM

MAX

UNIT

f(DCO03)

Rsel = 0, DCO = 3, MOD = 0, DCOR = 0, TA = 25°C

VCC = 3 V

0.12

MHz

f(DCO03)

Rsel = 0, DCO = 3, MOD = 0, DCOR = 0, TA = 25°C

VCC = 5 V

0.13

MHz

f(DCO13)

Rsel = 1, DCO = 3, MOD = 0, DCOR = 0, TA = 25°C

VCC = 3 V

0.19

MHz

f(DCO13)

Rsel = 1, DCO = 3, MOD = 0, DCOR = 0, TA = 25°C

VCC = 5 V

0.21

MHz

f(DCO23)

Rsel = 2, DCO = 3, MOD = 0, DCOR = 0, TA = 25°C

VCC = 3 V

0.31

MHz

f(DCO23)

Rsel = 2, DCO = 3, MOD = 0, DCOR = 0, TA = 25°C

VCC = 5 V

0.34

MHz

f(DCO33)

Rsel = 3, DCO = 3, MOD = 0, DCOR = 0, TA = 25°C

VCC = 3 V

0.5

MHz

f(DCO33)

Rsel = 3, DCO = 3, MOD = 0, DCOR = 0, TA = 25°C

VCC = 5 V

0.55

MHz

f(DCO43)

Rsel = 4, DCO = 3, MOD = 0, DCOR = 0, TA = 25°C

VCC = 3 V

0.5

0.8

1.1

MHz

f(DCO43)

Rsel = 4, DCO = 3, MOD = 0, DCOR = 0, TA = 25°C

VCC = 5 V

0.6

0.9

1.2

MHz

f(DCO53)

Rsel = 5, DCO = 3, MOD = 0, DCOR = 0, TA = 25°C

VCC = 3 V

0.9

1.2

1.55

MHz

f(DCO53)

Rsel = 5, DCO = 3, MOD = 0, DCOR = 0, TA = 25°C

VCC = 5 V

1.1

1.4

1.7

MHz

f(DCO63)

Rsel = 6, DCO = 3, MOD = 0, DCOR = 0, TA = 25°C

VCC = 3 V

1.7

2

2.3

MHz

f(DCO63)

Rsel = 6, DCO = 3, MOD = 0, DCOR = 0, TA = 25°C

VCC = 5 V

2.1

2.4

2.7

MHz

f(DCO73)

Rsel = 7, DCO = 3, MOD = 0, DCOR = 0, TA = 25°C

VCC = 3 V

2.8

3.1

3.5

MHz

f(DCO73)

Rsel = 7, DCO = 3, MOD = 0, DCOR = 0, TA = 25°C

VCC = 5 V

3.8

4.2

4.5

MHz

f(DCO47)

Rsel = 4, DCO = 7, MOD = 0, DCOR = 0, TA = 25°C

VCC = 3 V/5 V

FDCO40 FDCO40 FDCO40

MHz

f(DCO47)

Rsel = 4, DCO = 7, MOD = 0, DCOR = 0, TA = 25°C

VCC = 3 V/5 V

FDCO40

x1.8

FDCO40

x2.2

FDCO40

x2.6

MHz

S(Rsel)

SR = fRsel+1/fRsel

VCC = 3 V/5 V

1.4

1.65

1.9

ratio

S(DCO)

SDCO = fDCO+1/fDCO

VCC = 3 V/5 V

1.07

1.12

1.16

ratio

Dt

Temperature drift, Rsel = 4, DCO = 3,

VCC = 3 V

−0.31

−0.36

−0.40

%/

°C

Dt

Temperature drift, Rsel = 4, DCO = 3,

MOD = 0 (see Note 1)

VCC = 5 V

−0.33

−0.38

−0.43

%/

°C

DV

Drift with VCC variation, Rsel = 4, DCO = 3,

MOD = 0 (see Note 1)

VCC = 3 V to 5 V

0

5

10

%/V

NOTE 1: These parameters are not production tested.