CY74FCT480ATPC datasheet(4/8 Pages) TI

4 / 8 page

CY54/74FCT480T

Power Supply Characteristics

Parameter

Description

Test Conditions

Typ.[4]

Max.

Unit

ICC

Quiescent Power Supply Current

VCC=Max., VIN < 0.2V,

VIN > VCC–0.2V

0.1

0.2

∆I

Quiescent Power Supply Current

(TTL inputs HIGH)

VCC=Max., VIN=3.4V,

[7]

f1=0, Outputs Open

0.5

2.0

ICCD

Dynamic Power Supply Current[8]

VCC=Max., One Bit Toggling,

50% Duty Cycle, Outputs Open,

VIN < 0.2V or VIN > VCC–0.2V

0.06

0.12

mA/

MHz

Total Power Supply Current[9]

VCC=Max.,

50% Duty Cycle, Outputs Open,

One Bit Toggling at f1=2.5 MHz,

VIN < 0.2V or VIN > VCC–0.2V

0.7

1.4

VCC=Max.,

50% Duty Cycle, Outputs Open,

One Bit Toggling at f1=2.5 MHz,

VIN=3.4V or VIN=GND

1.0

2.4

VCC=Max.,

50% Duty Cycle, Outputs Open,

Sixteen Bits Toggling at f1=2.5 MHz,

VIN < 0.2V or VIN > VCC–0.2V

2.5

5.0[10]

VCC=Max.,

50% Duty Cycle, Outputs Open,

Sixteen Bits Toggling at f1=2.5 MHz,

VIN=3.4V or VIN=GND

6.5

21.0[10]

Switching Characteristics Over the Operating Range

Description

FCT480AT

FCT480BT

Unit

Com’l

Military

Com’l

tPLH

tPHL

Propagation Delay

A to EVEN/ODD

7.5

7.0

6.6

5.6

tPLH

[11]

tPHL

Propagation Delay

A to ERROR

7.0

8.5

7.0

8.1

5.6

6.5

tPLH

tPHL

Propagation Delay

CHK/GEN to EVEN/ODD

6.5

7.5

6.3

7.4

5.9

tPLH

[11]

tPHL

Propagation Delay

CHK/GEN to ERROR

7.5

7.0

7.1

6.9

5.7

5.5

Notes:

Per TTL driven input (VIN=3.4V); all other inputs at VCC or GND.

This parameter is not directly testable, but is derived for use in Total Power Supply calculations.

=IQUIESCENT + IINPUTS + IDYNAMIC

=ICC+∆ICCDHNT+ICCD(f0/2 + f1N1)

ICC = Quiescent Current with CMOS input levels

∆I

CC = Power Supply Current for a TTL HIGH input (VIN=3.4V)

DH = Duty Cycle for TTL inputs HIGH

= Number of TTL inputs at DH

ICCD = Dynamic Current caused by an input transition pair (HLH or LHL)

= Clock frequency for registered devices, otherwise zero

= Input signal frequency

= Number of inputs changing at f1

All currents are in milliamps and all frequencies are in megahertz.

10. Values for these conditions are examples of the ICC formula. These limits are speciﬁed but not tested.

11. tPLH is measured up to VOUT=VOL+0.3V

CY74FCT480ATPC Datasheet(PDF) 4 Page - Texas Instruments

CY74FCT480ATPC Datasheet(HTML) 4 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8

Datasheet Descarga

Enlace URL