LT1057/LT1058

16

10578fc

Linear Technology Corporation

1630 McCarthy Blvd., Milpitas, CA 95035-7417

© LINEAR TECHNOLOGY CORPORATION 1989

LT 0108 REV C • PRINTED IN USA

RELATED PARTS

TYPICAL APPLICATION

PART NUMBER

DESCRIPTION

COMMENTS

LT1055/6

Precision, High Speed, JFET Input

Operational Amplifiers

12V/μs Slew Rate, 5.5MHz Bandwidth

LT1880

SOT-23, Rail-to-Rail Output, Picoamp Input

Precision Op Amps

150μV Max Offset Voltage, 900pA Max Input Bias Current

LT1881/2

Dual and Quad Rail-to-Rail Output, Picoamp Input

Precision Op Amps

50μV Max Offset Voltage, 200pA Max Input Bias Current

LT1884/5

Dual/Quad Rail-to-Rail Output, Picoamp Input

Precision Op Amps

50μV Max Offset Voltage, 400pA Max Input Bias Current

LT6010

135μA, 14nV/rtHz, Rail-to-Rail Output, Precision

Low Power Op Amp with Shutdown

35μV Max Offset Voltage, 300pA Max Input Bias Current

LT6011/12

Dual/Quad 135μA, 14nV/rtHz, Rail-to-Rail Output

Precision Low Power Op Amp

60μV Max Offset Voltage, 300pA Max Input Bias Current

LTC6078/9

Micropower Precision, Dual/Quad CMOS

Rail-to-Rail Input/Output Amplifiers

Maximum Offset Drift: 0.7μV/°C

LTC6241/2

Dual/Quad 18MHz, Low Noise, Rail-to-Rail

CMOS Op Amps

O.1Hz to 10Hz Noise: 550n Vpp

S16 (WIDE) 0502

NOTE 3

.398 – .413

(10.109 – 10.490)

NOTE 4

16

15

14

13

12

11

10

9

1

N

23

4

5

6

78

N/2

.394 – .419

(10.007 – 10.643)

.037 – .045

(0.940 – 1.143)

.004 – .012

(0.102 – 0.305)

.093 – .104

(2.362 – 2.642)

.050

(1.270)

BSC

.014 – .019

(0.356 – 0.482)

TYP

0

° – 8° TYP

NOTE 3

.009 – .013

(0.229 – 0.330)

.005

(0.127)

RAD MIN

.016 – .050

(0.406 – 1.270)

.291 – .299

(7.391 – 7.595)

NOTE 4

× 45°

.010 – .029

(0.254 – 0.737)

INCHES

(MILLIMETERS)

NOTE:

1. DIMENSIONS IN

2. DRAWING NOT TO SCALE

3. PIN 1 IDENT, NOTCH ON TOP AND CAVITIES ON THE BOTTOM OF PACKAGES ARE THE MANUFACTURING OPTIONS.

THE PART MAY BE SUPPLIED WITH OR WITHOUT ANY OF THE OPTIONS

4. THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.

MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .006" (0.15mm)

.420

MIN

.325

±.005

RECOMMENDED SOLDER PAD LAYOUT

.045

±.005

N

12

3

N/2

.050 BSC

.030

±.005

TYP

SW Package

16-Lead Plastic Small Outline (Wide .300 Inch)

(Reference LTC DWG # 05-08-1620)