| Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
MH1RT Datasheet(PDF) 11 Page - ATMEL Corporation |
|
|
|||||||||||||||||||||||||||||
MH1RT Datasheet(HTML) 11 Page - ATMEL Corporation |
|
11 / 20 page ![]() 11 4110K–AERO–11/07 MH1RT Applicable over recommended operating temperature and voltage range unless otherwise noted. IICS Cold sparing leakage input current PICZ Vdd = Vss = 0V Vin = 0 to VDD Max -2 -2 µA IOCS Cold sparing leakage output current POxxZ Vdd = Vss = 0V Vin = 0 to VDD Max -2 -2 µA VCSTH (3) Supply threshold of cold sparing buffers POxxZ Iocs = 100 µA 0.5 V VOL Low-level Output Voltage (4) PO11 IOL = 2 mA, Vdd = Vdd(Min.) 0.4 V VOH High level output voltage (5) PO11 Ioh = -1.8 mA, Vdd = Vdd(Min.) 2.4 V IOS Output short circuit current Iosn Iosp PO11 PO11 Vdd = Vdd(Max.), Vout = Vdd Vouy = Vss 23 13 mA ICCSB Leakage current per cell Vdd = Vdd(Max.) 0.7 5 nA ICCOP Dynamic current per gate Vdd = Vdd(Max.) 0.69 µW/MHz 1. For standard pull-ups: PRU(#), # = {1-31} index for Ron: Ron = # x RO where RO = 14 kΩ typ, 25 kΩ Max., 9 kΩ Min. 2. For standard pull-downs:PRD(#), # = {1-31} index for Ron: Ron = # x RO where RO = 8kΩ typ, 20 kΩ Max., 4 kΩ Min. 3. Guaranteed not tested. 4. For output buffers PO (1-C) (1-C): 1-C: hex value: convert hex to kΩ x IO = p and n-channel output drive IO = -2.0 mA for standard buffers (including cold sparing) measured at Vol = 0.4V 5. For output buffers PO (1-C) (1-C): 1-C: hex value: convert hex to kΩ x IO = p and n-channel output drive IO = -2.0 mA for standard buffers (including cold sparing) measured at Voh = 2.4V Table 5. 3.3V DC Characteristics (Continued) Symbol Parameter Buffer Test Condition Min. Typ Max. Units Table 6. 5V DC Characteristics Symbol Parameter Buffer Test Condition Min. Typ Max. Units TA Operating Temperature All -55 25 125 C Vdd Supply Voltage 5V Tolerant 3.0 3.3 3.6 V Vcc Supply Voltage 5V Compliant 4.5 5 5.5 V IIL Low-level Input Current Pull-up resistors PRU1 (1) Pull down resistor PRD1 CMOS VIN = VSS -1 180 -5 1 690 5 µA IIH High level Input Current Pull-up resistors PRU1 Pull down resistor PRD1 (2) CMOS VIN = VDD( Max.) -1 -5 30 1 5 400 µA Ioz High impedance state output current All Vin = Vdd orVss,Vdd=Vdd(max No pull resistor -1 1 µA |
|
|
Enlace URL |
| ¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Enlace a la hoja de datos | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |