M38048F2HKP datasheet(45/387 Pages) RENESAS

45 / 387 page

1-27

REJ09B0212-0100Z

Rev.1.00

Jan 14, 2005

3804 Group (Spec.H)

HARDWARE

FUNCTIONAL DESCRIPTION

TIMERS

q8-bit Timers

The 3804 group (Spec. H) has four 8-bit timers: timer 1, timer 2,

timer X, and timer Y.

The timer 1 and timer 2 use one prescaler in common, and the

timer X and timer Y use each prescaler. Those are 8-bit

prescalers. Each of the timers and prescalers has a timer latch or

a prescaler latch.

The division ratio of each timer or prescaler is given by 1/(n + 1),

where n is the value in the corresponding timer or prescaler latch.

All timers are down-counters. When the timer reaches “0016”, an

underflow occurs at the next count pulse and the contents of the

corresponding timer latch are reloaded into the timer and the

count is continued. When the timer underflows, the interrupt re-

quest bit corresponding to that timer is set to “1”.

qTimer divider

The divider count source is switched by the main clock division

ratio selection bits of CPU mode register (bits 7 and 6 at address

003B16). When these bits are “00” (high-speed mode) or “01”

(middle-speed mode), XIN is selected. When these bits are“10”

(low-speed mode), XCIN is selected.

qPrescaler 12

The prescaler 12 counts the output of the timer divider. The count

source is selected by the timer 12, X count source selection

1/1024 of f(XIN) or f(XCIN).

Timer 1 and Timer 2

The timer 1 and timer 2 counts the output of prescaler 12 and pe-

riodically set the interrupt request bit.

qPrescaler X and prescaler Y

The prescaler X and prescaler Y count the output of the timer

divider or f(XCIN). The count source is selected by the timer 12, X

count source selection register (address 000E16) and the timer Y,

Z count source selection register (address 000F16) among 1/2,

1/4, 1/8, 1/16, 1/32, 1/64, 1/128, 1/256, 1/512, and 1/1024 of f(XIN)

or f(XCIN); and f(XCIN).

Timer X and Timer Y

The timer X and timer Y can each select one of four operating

modes by setting the timer XY mode register (address 002316).

(1) Timer mode

qMode selection

This mode can be selected by setting “00” to the timer X operating

mode bits (bits 1 and 0) and the timer Y operating mode bits (bits

5 and 4) of the timer XY mode register (address 002316).

qExplanation of operation

The timer count operation is started by setting “0” to the timer X

count stop bit (bit 3) and the timer Y count stop bit (bit 7) of the

timer XY mode register (address 002316).

When the timer reaches “0016”, an underflow occurs at the next

count pulse and the contents of timer latch are reloaded into the

timer and the count is continued.

(2) Pulse output mode

qMode selection

This mode can be selected by setting “01” to the timer X operating

mode bits (bits 1 and 0) and the timer Y operating mode bits (bits

5 and 4) of the timer XY mode register (address 002316).

qExplanation of operation

The operation is the same as the timer mode’s. Moreover the

pulse which is inverted each time the timer underflows is output

from CNTR0/CNTR1 pin. Regardless of the timer counting or not

the output of CNTR0/CNTR1 pin is initialized to the level of speci-

fied by their active edge switch bits when writing to the timer.

When the CNTR0 active edge switch bit (bit 2) and the CNTR1 ac-

tive edge switch bit (bit 6) of the timer XY mode register (address

002316) is “0”, the output starts with “H” level. When it is “1”, the

output starts with “L” level.

Switching the CNTR0 or CNTR1 active edge switch bit will reverse

the output level of the corresponding CNTR0 or CNTR1 pin.

sPrecautions

Set the double-function port of CNTR0/CNTR1 pin and port P54/

P55 to output in this mode.

M38048F2HKP Datasheet(PDF) 45 Page - Renesas Technology Corp

M38048F2HKP Datasheet(HTML) 45 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Descarga

Enlace URL