M38040F9HKP datasheet(88/116 Pages) RENESAS

88 / 116 page

Rev.1.01

Jan 25, 2005

page 88 of 114

REJ03B0131-0101Z

3804 Group (Spec. H)

q Functions To Inhibit Rewriting Flash

Memory Version

To prevent the contents of internal flash memory from being read

out or rewritten easily, this MCU incorporates a ROM code protect

function for use in parallel I/O mode and an ID code check func-

tion for use in standard serial I/O mode.

(1) ROM Code Protect Function

The ROM code protect function is the function to inhibit reading

out or modifying the contents of internal flash memory by using

the ROM code protect control address (address FFDB16) in paral-

lel I/O mode. Figure 85 shows the ROM code protect control

address (address FFDB16). (This address exists in the User ROM

area.)

If one or both of the pair of ROM code protect bits is set to “0”, the

ROM code protect is turned on, so that the contents of internal

flash memory are protected against readout and modification. The

ROM code protect is implemented in two levels. If level 2 is se-

lected, the flash memory is protected even against readout by a

shipment inspection LSI tester, etc. When an attempt is made to

select both level 1 and level 2, level 2 is selected by default.

If both of the two ROM code protect reset bits are set to “00”, the

ROM code protect is turned off, so that the contents of internal

flash memory can be readout or modified. Once the ROM code

protect is turned on, the contents of the ROM code protect reset

bits cannot be modified in parallel I/O mode. Use the serial I/O or

CPU rewrite mode to rewrite the contents of the ROM code protect

reset bits.

Rewriting of only the ROM code protect control address (address

FFDB16) cannot be performed. When rewriting the ROM code pro-

tect reset bit, rewrite the whole user ROM area (block 0)

containing the ROM code protect control address.

Fig. 85 Structure of ROM code protect control address

ROM code protect control address (address FFDB16)

ROMCP (FF16 when shipped)

Reserved bits (“1” at read/write)

ROM code protect level 2 set bits (ROMCP2) (Notes 1, 2)

b3b2

0 0: Protect enabled

0 1: Protect enabled

1 0: Protect enabled

1 1: Protect disabled

ROM code protect reset bits (ROMCR) (Note 3)

b5b4

0 0: Protect removed

0 1: Protect set bits effective

1 0: Protect set bits effective

1 1: Protect set bits effective

ROM code protect level 1 set bits (ROMCP1) (Note 1)

b7b6

0 0: Protect enabled

0 1: Protect enabled

1 0: Protect enabled

1 1: Protect disabled

Notes 1: When ROM code protect is turned on, the internal flash memory is protected

against readout or modification in parallel I/O mode.

2: When ROM code protect level 2 is turned on, ROM code readout by a shipment

inspection LSI tester, etc. also is inhibited.

3: The ROM code protect reset bits can be used to turn off ROM code protect level 1

and ROM code protect level 2. However, since these bits cannot be modified in

parallel I/O mode, they need to be rewritten in serial I/O mode or CPU rewrite

mode.

M38040F9HKP Datasheet(PDF) 88 Page - Renesas Technology Corp

M38040F9HKP Datasheet(HTML) 88 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Descarga

Enlace URL