M38047F6HKP datasheet(48/116 Pages) RENESAS

48 / 116 page

Rev.1.01

Jan 25, 2005

page 48 of 114

REJ03B0131-0101Z

3804 Group (Spec. H)

(2) Asynchronous Serial I/O (UART) Mode

Clock asynchronous serial I/O mode (UART) can be selected by

clearing the serial I/O3 mode selection bit of the serial I/O3 control

Eight serial data transfer formats can be selected, and the transfer

formats used by a transmitter and receiver must be identical.

The transmit and receive shift registers each have a buffer, but the

two buffers have the same address in a memory. Since the shift

written to the transmit buffer register, and receive data is read

from the receive buffer register.

The transmit buffer register can also hold the next data to be

transmitted, and the receive buffer register can hold a character

while the next character is being received.

Fig. 42 Block diagram of UART serial I/O3

Fig. 43 Operation of UART serial I/O3

f(XIN)

1/4

PEFE

1/16

Data bus

Receive buffer register 3

Address 003016

Receive shift register 3

Receive buffer full flag (RBF)

Receive interrupt request (RI)

Baud rate generator 3

Frequency division ratio 1/(n+1)

Address 002F16

ST/SP/PA generator

Transmit buffer register 3

Data bus

Transmit shift register 3

Address 003016

Transmit shift completion flag (TSC)

Transmit buffer empty flag (TBE)

Transmit interrupt request (TI)

Address 003116

ST detector

SP detector

UART3 control register

Address 003316

Character length selection bit

Address 003216

BRG count source selection bit

Transmit interrupt source selection bit

Serial I/O3 synchronous clock selection bit

Clock control circuit

Character length selection bit

7 bits

8 bits

Serial I/O3 control register

P36/SCLK3

Serial I/O3 status register

P34/RXD3

P35/TXD3

(f(XCIN) in low-speed mode)

TSC=0

TBE=1

RBF=0

TBE=0

RBF=1

TBE=1

TSC=1

Transmit or receive clock

Transmit buffer write

signal

Generated at 2nd bit in 2-stop-bit mode

1 start bit

7 or 8 data bit

1 or 0 parity bit

1 or 2 stop bit (s)

1: Error flag detection occurs at the same time that the RBF flag becomes “1” (at 1st stop bit, during reception).

2: As the transmit interrupt (TI), when either the TBE or TSC flag becomes “1,” can be selected to occur depending on the setting of the transmit

interrupt source selection bit (TIC) of the serial I/O3 control register.

3: The receive interrupt (RI) is set when the RBF flag becomes “1.”

4: After data is written to the transmit buffer when TSC=1, 0.5 to 1.5 cycles of the data shift cycle are necessary until changing to TSC=0.

Notes

✽

Serial output TXD3

Serial input RXD3

Receive buffer read

signal

M38047F6HKP Datasheet(PDF) 48 Page - Renesas Technology Corp

M38047F6HKP Datasheet(HTML) 48 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Descarga

Enlace URL