M38043F2HKP datasheet(39/116 Pages) RENESAS

39 / 116 page

Rev.1.01

Jan 25, 2005

page 39 of 114

REJ03B0131-0101Z

3804 Group (Spec. H)

SERIAL INTERFACE

Serial I/O1

Serial I/O1 can be used as either clock synchronous or asynchro-

nous (UART) serial I/O1. A dedicated timer is also provided for

baud rate generation.

(1) Clock Synchronous Serial I/O Mode

Clock synchronous serial I/O1 mode can be selected by setting

the serial I/O1 mode selection bit of the serial I/O1 control register

(bit 6 of address 001A16) to “1”.

For clock synchronous serial I/O, the transmitter and the receiver

must use the same clock. If an internal clock is used, transfer is

started by a write signal to the transmit/receive buffer register.

Fig. 32 Block diagram of clock synchronous serial I/O1

Fig. 33 Operation of clock synchronous serial I/O1

1/4

F/F

P46/SCLK1

Serial I/O1 status register

Serial I/O1 control register

P47/SRDY1

P44/RXD1

P45/TXD1

Receive buffer register 1

Address 001816

Receive shift register 1

Receive buffer full flag (RBF)

Receive interrupt request (RI)

Clock control circuit

Shift clock

Serial I/O1 synchronous

clock selection bit

Frequency division ratio 1/(n+1)

Baud rate generator 1

Address 001C16

BRG count source selection bit

Clock control circuit

Falling-edge detector

Transmit buffer register 1

Data bus

Address 001816

Shift clock

Transmit shift completion flag (TSC)

Transmit buffer empty flag (TBE)

Transmit interrupt request (TI)

Transmit interrupt source selection bit

Address 001916

Data bus

Address 001A16

Transmit shift register 1

f(XIN)

(f(XCIN) in low-speed mode)

RBF = 1

TSC = 1

TBE = 0

TBE = 1

TSC = 0

Transfer shift clock

(1/2 to 1/2048 of the internal

clock, or an external clock)

Serial output TxD1

Serial input RxD1

Write pulse to receive/transmit

buffer register (address 001816)

Overrun error (OE)

detection

Notes 1: As the transmit interrupt (TI), which can be selected, either when the transmit buffer has emptied (TBE=1) or after the

transmit shift operation has ended (TSC=1), by setting the transmit interrupt source selection bit (TIC) of the serial I/O1

control register.

2: If data is written to the transmit buffer register when TSC=0, the transmit clock is generated continuously and serial data

is output continuously from the TxD pin.

3: The receive interrupt (RI) is set when the receive buffer full flag (RBF) becomes “1” .

Receive enable signal SRDY1

M38043F2HKP Datasheet(PDF) 39 Page - Renesas Technology Corp

M38043F2HKP Datasheet(HTML) 39 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Descarga

Enlace URL