| Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
CN-14A-R-C2 Datasheet(PDF) 12 Page - Panasonic Semiconductor |
|
|
|||||||||||||||||||||||||||||
CN-14A-R-C2 Datasheet(HTML) 12 Page - Panasonic Semiconductor |
|
12 / 16 page ![]() Dual Display Digital Pressure Sensor DP-100 SERIES Ver.2 746 Selection Guide Pressure/ Digital Display Pressure/ Head-separated Flow DP-100 DP-M FIBER SENSORS LASER SENSORS PHOTO- ELECTRIC SENSORS MICRO PHOTO- ELECTRIC SENSORS AREA SENSORS LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASURE- MENT SENSORS STATIC ELECTRICITY PREVENTION DEVICES LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Never use this product as a sensing device for personnel protection. In case of using sensing devices for personnel protection, use products which meet laws and standards, such as OSHA, ANSI or IEC etc., for personnel protection applicable in each region or country. The DP-100 series is designed for use with non-corrosive gas. It cannot be used with liquid or corrosive gas. • • • Wiring Make sure that the power supply is off while wiring. Verify that the supply voltage variation is within the rating. If power is supplied from a commercial switching regulator, ensure that the frame ground (F.G.) terminal of the power supply is connected to an actual ground. In case noise generating equipment (switching regulator, inverter motor, etc.) is used in the vicinity of this sensor, connect the frame ground (F.G.) terminal of the equipment to an actual ground. Do not run the wires together with high-voltage lines or power lines or put them in the same raceway. This can cause malfunction due to induction. Incorrect wiring will cause problems with operation. • • • • • • Connection Do not apply stress directly to the connection cable leader or to the connector. • Connector attached cable [ CN-14A(-R)-C□] The MS-DP1-2 panel mounting bracket (optional) and the MS-DP1-3 front protection cover (optional) are also available. • Mounting Part description MS-DP1-1 / MS-DP1-5 sensor mounting brackets are available separately, and it should be used for mounting. When tightening the sensor to the sensor mounting bracket, use a tightening torque of 0.5 N·m or less. • Sensor mounting bracket MS-DP1-1 (Optional) M3 (length 6 mm 0.236 in) screws with washers Accessory for MS-DP1-1 and MS-DP1-5 Front protection cover MS-DP1-3 (optional) Panel mounting bracket MS-DP1-2 (optional) ( ) Decide the direction of this product to mount with the sensor. Mount this product with the M3 female threads of the sensor by using the attached M3 (length 8 mm 0.315 in) screws. The tightening torque should be 0.5 N·m or less. Mount this product with the mounting surface by using the attached M4 (length 20 mm 0.787 in) screws. The tightening torque should be 1.2 N·m or less. Note: It is not possible to mount this product such that the pressure port faces upward. Note: Take care that if the cable with connector is sticking out of the side groove of this product when mounting, the cable may disconnected. The MS-DP1-4 panel mounting bracket is available when switching from the DP2 / DP3 series. • An conversion bushing is available for when using the DP-10□-M short pressure port type. It can be used to switch between this model and the DP2 / DP3 series. When connecting to the pressure port, use a tightening torque of 1.0 N·m or less. • The MS-DP1-F□ flat attachment is available. If using the MS-DP1-F□ flat attachment (optional), install by following the procedures given below. • Pressure port faces downward Pressure port faces leftward Pressure port faces rightward Pressure port faces upward M3 (length 8 mm 0.315 in) screw (Accessory) M3 female thread M3 female thread Connector attached cable Groove M4 (length 20 mm 0.787 in) screw (Accessory) DP2-20 ñ101.3kP a OUT2 OUT1 MODE 0-AD J Front protective cover DPX-04 (Optional) can be installed on MS-DP1-4. DP2 / DP3 DP-100 Insert Remove Remove Panel mounting bracket MS-DP1-4 Conversion bushing MS-DP1-7 M5 female thread Rc 1 8 female thread Mounting holes for DP2 / DP3 series can be used as is. 1 2 3 Main display Sub display Decrement key Increment key Mode selection key Comparative Output 1 operation indicator Comparative Output 2 operation indicator Work as analog voltage output operation indicator in Multi-function type PRECAUTIONS FOR PROPER USE Refer to p.1472 for general precautions. |
|
|
Enlace URL |
| ¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Enlace a la hoja de datos | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |