PIC16F753 datasheet(107/230 Pages) MICROCHIP

107 / 230 page

 2013-2015 Microchip Technology Inc.

DS40001709C-page 107

PIC16F753/HV753

12.1.6

RESULT FORMATTING

The 10-bit A/D conversion result can be supplied in two

formats, left justified or right justified. The ADFM bit of

the ADCON0 register controls the output format.

Figure 12-4 shows the two output formats.

FIGURE 12-3:

10-BIT A/D CONVERSION RESULT FORMAT

12.2

ADC Operation

12.2.1

STARTING A CONVERSION

To enable the ADC module, the ADON bit of the

ADCON0 register must be set to a ‘1’. Setting the GO/

DONE bit of the ADCON0 register to a ‘1’ will start the

Analog-to-Digital conversion.

12.2.2

COMPLETION OF A CONVERSION

When the conversion is complete, the ADC module will:

• Clear the GO/DONE bit

• Set the ADIF flag bit

• Update the ADRESH:ADRESL registers with new

conversion result

12.2.3

TERMINATING A CONVERSION

If a conversion must be terminated before completion,

the GO/DONE bit can be cleared in software. The

ADRESH:ADRESL registers will not be updated with

the partially complete Analog-to-Digital conversion

sample. Instead, the ADRESH:ADRESL register pair

will retain the value of the previous conversion. Addi-

tionally, a 2 TAD delay is required before another acqui-

sition can be initiated. Following this delay, an input

acquisition is automatically started on the selected

channel.

12.2.4

ADC OPERATION DURING SLEEP

The ADC module can operate during Sleep. This

requires the ADC clock source to be set to the FRC

option. When the FRC clock source is selected, the

ADC waits one additional instruction before starting the

conversion. This allows the SLEEP instruction to be

executed, which can reduce system noise during the

conversion. If the ADC interrupt is enabled, the device

will

wake-up

from

Sleep

when

the

conversion

completes. If the ADC interrupt is disabled, the ADC

module is turned off after the conversion completes,

although the ADON bit remains set.

When the ADC clock source is something other than

FRC,

SLEEP

instruction

causes

the

present

conversion to be aborted and the ADC module is

turned off, although the ADON bit remains set.

12.2.5

SPECIAL EVENT TRIGGER

The CCP Special Event Trigger allows periodic ADC

measurements without software intervention. When

this trigger occurs, the GO/DONE bit is set by hardware

and the Timer1 counter resets to zero.

Using the Special Event Trigger does not assure proper

ADC timing. It is the user’s responsibility to ensure that

the ADC timing requirements are met.

See

Section 10.0

“Capture/Compare/PWM

Modules” for more information.

ADRESH

ADRESL

(ADFM = 0)MSB

LSB

bit 7

bit 0

bit 7

bit 0

10-bit A/D Result

Unimplemented: Read as ‘0’

(ADFM = 1)

MSB

LSB

bit 7

bit 0

bit 7

bit 0

Unimplemented: Read as ‘0’

10-bit A/D Result

Note:

The GO/DONE bit should not be set in the

same instruction that turns on the ADC.

Refer to Section 12.2.6 “A/D Conver-

sion Procedure”.

Note:

A device Reset forces all registers to their

Reset state. Thus, the ADC module is

turned off and any pending conversion is

terminated.

PIC16F753 Datasheet(PDF) 107 Page - Microchip Technology

PIC16F753 Datasheet(HTML) 107 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Descarga

Enlace URL