PIC12LF1501 datasheet(171/352 Pages) MICROCHIP

171 / 352 page

 2011-2015 Microchip Technology Inc.

DS40001607D-page 171

PIC16(L)F1503

This is a step by step process of what typically must

be done to accomplish I2C communication.

Start bit detected.

S bit of SSPxSTAT is set; SSPxIF is set if inter-

rupt on Start detect is enabled.

Matching address with R/W bit clear is received.

The slave pulls SDAx low sending an ACK to the

master, and sets SSPxIF bit.

Software clears the SSPxIF bit.

Software reads received address from

SSPxBUF clearing the BF flag.

If SEN = 1; Slave software sets CKP bit to

release the SCLx line.

The master clocks out a data byte.

Slave drives SDAx low sending an ACK to the

master, and sets SSPxIF bit.

10. Software clears SSPxIF.

11. Software reads the received byte from

SSPxBUF clearing BF.

12. Steps 8-12 are repeated for all received bytes

from the Master.

13. Master sends Stop condition, setting P bit of

SSPxSTAT, and the bus goes idle.

21.5.2.2

7-bit Reception with AHEN and DHEN

Slave device reception with AHEN and DHEN set

operate the same as without these options with extra

interrupts and clock stretching added after the eighth

falling edge of SCLx. These additional interrupts allow

the slave software to decide whether it wants to ACK

the receive address or data byte, rather than the hard-

ware. This functionality adds support for PMBus™ that

was not present on previous versions of this module.

This list describes the steps that need to be taken by

slave software to use these options for I2C communi-

cation. Figure 21-16 displays a module using both

address and data holding. Figure 21-17 includes the

operation with the SEN bit of the SSPxCON2 register

set.

S bit of SSPxSTAT is set; SSPxIF is set if inter-

rupt on Start detect is enabled.

Matching address with R/W bit clear is clocked

in. SSPxIF is set and CKP cleared after the

eighth falling edge of SCLx.

Slave clears the SSPxIF.

Slave can look at the ACKTIM bit of the

SSPxCON3 register to determine if the SSPxIF

was after or before the ACK.

Slave reads the address value from SSPxBUF,

clearing the BF flag.

Slave sets ACK value clocked out to the master

by setting ACKDT.

Slave releases the clock by setting CKP.

SSPxIF is set after an ACK, not after a NACK.

If SEN = 1 the slave hardware will stretch the

clock after the ACK.

10. Slave clears SSPxIF.

11. SSPxIF set and CKP cleared after eighth falling

edge of SCLx for a received data byte.

12. Slave looks at ACKTIM bit of SSPxCON3 to

determine the source of the interrupt.

13. Slave reads the received data from SSPxBUF

clearing BF.

14. Steps 7-14 are the same for each received data

byte.

15. Communication is ended by either the slave

sending an ACK = 1, or the master sending a

Stop condition. If a Stop is sent and Interrupt on

Stop Detect is disabled, the slave will only know

by polling the P bit of the SSPSTAT register.

Note:

SSPxIF is still set after the ninth falling edge

of SCLx even if there is no clock stretching

and BF has been cleared. Only if NACK is

sent to master is SSPxIF not set

PIC12LF1501 Datasheet(PDF) 171 Page - Microchip Technology

PIC12LF1501 Datasheet(HTML) 171 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Descarga

Enlace URL