| Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
PCM1738E/2K.B Datasheet(PDF) 32 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
PCM1738E/2K.B Datasheet(HTML) 32 Page - Texas Instruments |
|
32 / 47 page ![]() www.ti.com Analog Gain by Balanced Amplifier REFERENCE CURRENT RESISTOR APPLICATION FOR EXTERNAL DIGITAL FILTER INTERFACE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 28 27 26 25 24 23 22 21 20 19 18 17 16 15 WDCK(WordClock) DATA-L BCK SCK DATA-R DF1704 DF1706 PMD200 Mode Control RST ZEROL ZEROR WDCK(LRCK) DATAL (DATA) BCK SCKI DGND V DD SCKO MDO MDI MC CS V 3 CC AGND2 I OUTL– I OUTL+ V CC2 V CC1 V COM3 I REF V COM2 V COM1 AGND1 I OUTR+ I OUTR– DATAR(MUTE) Analog OutputStage SameasStandard Application B0201-01 ():OriginalPinName APPLICATIONS FOR INTERFACING WITH THE EXTERNAL DIGITAL FILTER PCM1738 SBAS174C – FEBRUARY 2002 – REVISED FEBRUARY 2007 The I/V converters are followed by balanced amplifier stages that sum the differential signals for each channel, creating a single-ended voltage output. In addition, the balanced amplifiers provide a second-order, low-pass filter function that band-limits the audio output signal. The cutoff frequency and gain is given by external R and C component values. In the case of Figure 40, the cutoff frequency is 45 kHz with a gain of 1. The output voltage for each channel is 6.2 Vp-p, or 2.2 Vrms. As shown in the analog output application circuit, marked R1 on Figure 40, there is a resistor connected from IREF (pin 21) to the analog ground, designated as R1. This resistor sets the current for the internal reference circuit. The value of R1 must be 16 kΩ, ±1% in order to match the specified gain error shown in the Electrical Characteristics table. Figure 41. Connection Diagram for External Digital Filter (Internal DF Bypass Mode) Application For some applications, it may be desirable to use an external digital filter to perform the interpolation function, as it may provide improved stop-band attenuation or other special features not available with the PCM1738's internal digital filter. The PCM1738 supports the use of an external digital filter, including: • The DF1704 and DF1706 from Texas Instruments • Pacific Microsonics PMD100 HDCD filter/decoder ICs • Programmable digital signal processors 32 Submit Documentation Feedback |
|
Enlace URL |
| ¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Enlace a la hoja de datos | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |