PCD5003 datasheet(21/44 Pages) PHILIPS

21 / 44 page

1997 Jun 24

Philips Semiconductors

Product speciﬁcation

Advanced POCSAG Paging Decoder

PCD5003

7.31

Alert generation

The PCD5003 is capable of controlling 3 different alert

transducers: acoustic beeper (HIGH and LOW level), LED

and vibrator motor. The associated outputs are ATH/ATL,

LED and VIB respectively. ATL is an open drain output

capable of directly driving an acoustic alerter via a resistor.

The other outputs require external transistors.

Each alert output can be individually enabled via the alert

set-up register. Alert level and warble can be separately

selected. The alert pattern can either be standard

POCSAG or determined via the alert cadence register.

Direct alert control is possible via input ALC.

The alert set-up register is shown in Table 18.

Standard POCSAG alerts can be selected by setting

bit D0 in the alert set-up register, bits D6 and D7

determining the alert pattern used.

Automatic generation via all alert outputs of the POCSAG

alert pattern matching the received call type can be

enabled by SPF programming (SPF byte 03, bit D2).

7.32

Alert cadence register (03H; write)

When not programmed for POCSAG alerts (alert set-up

determines the alert pattern. Each bit represents a

62.5 ms time slot, a logic 1 activating the enabled alert

transducers. The bit pattern is rotated with the

MSB (bit D7) being output first and the LSB (bit D0) last.

When the last time slot (bit D0) is started an interrupt is

generated to allow loading of a new pattern. When the

pattern is not changed it will be repeated. Writing a zero to

the alert cadence register will halt alert generation.

7.33

Acoustic alert

Acoustic alerts are generated via outputs ATL and ATH.

For LOW level alerts only ATL is active, while for HIGH

level alerts ATH is also active. ATL is driven in counter

phase with ATH.

The alert level is controlled by bit D1 of the alert set-up

When D1 is reset, for standard POCSAG alerts (D0 = 1)

a LOW level acoustic alert is generated during the first

4 seconds (ATL), followed by 12 seconds at HIGH level

(ATL + ATH). When D1 is set, the full 16 seconds are at

HIGH level. An interrupt is generated upon expiry of the full

alert time.

When using the alert cadence register, D1 would normally

be updated by external control when the alert time-out

interrupt occurs at the start of the 8th cadence time slot.

Since D1 acts immediately on the alert level, it is advised

to reset the last bit of the previous pattern to prevent

unwanted audible level changes.

7.34

Vibrator alert

The vibrator output (VIB) is activated continuously during

a standard POCSAG alert or whenever the alert cadence

Two alert levels are supported: LOW level

(25 Hz square-wave) and HIGH level (continuous).

The vibrator level is controlled by bit D1 in the alert set-up

7.35

LED alert

The LED output pattern corresponds either to the selected

POCSAG alert or to the contents of the alert cadence

7.36

Warbled alert

When enabled by setting bit D2 in the alert set-up register,

the signals on outputs ATL, ATH and LED are warbled with

a 16 Hz modulation frequency. Output LED is switched on

and off at the modulation rate, while outputs ATL and ATH

switch between fAWH and fAWL alerter frequencies.

7.37

Direct alert control

A direct alert control input (ALC) is available for generating

user alarm signals (e.g. battery-low warning). A HIGH level

on input ALC activates all enabled alert outputs, overruling

any ongoing alert patterns.

7.38

Alert priority

Generation of a standard POCSAG alert (D0 = 1)

overrides any alert pattern in the alert cadence register.

After completion of the standard alert, the original cadence

is restarted from the position it was left at. The alert set-up

The highest priority has been assigned to the alert control

input (ALC). All enabled alert outputs will be activated

while ALC is set. Outputs are activated/deactivated

synchronous with the decoder clock. Activation requires

an extra delay of 1 clock when no alerts are being

generated.

When input ALC is reset, acoustic alerting does not cease

until the current output frequency cycle has been

completed.

PCD5003 Datasheet(PDF) 21 Page - NXP Semiconductors

PCD5003 Datasheet(HTML) 21 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44

Datasheet Descarga

Enlace URL