| Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
LAEX Datasheet(PDF) 9 Page - Linear Technology |
|
|
|||||||||||||||||||||||||||||
LAEX Datasheet(HTML) 9 Page - Linear Technology |
|
9 / 16 page ![]() 9 LT3020/LT3020-1.2/ LT3020-1.5/LT3020-1.8 sn3020 3020fas APPLICATIO S I FOR ATIO The LT3020 is a very low dropout linear regulator capable of 1V input supply operation. Devices supply 100mA of output current and dropout voltage is typically 150mV. Quiescent current is typically 120µA and drops to 3µA in shutdown. The LT3020 incorporates several protection features, making it ideal for use in battery-powered sys- tems. The device protects itself against reverse-input and reverse-output voltages. In battery backup applications where the output is held up by a backup battery when the input is pulled to ground, the LT3020 acts as if a diode is in series with its output which prevents reverse current flow. In dual supply applications where the regulator load is returned to a negative supply, the output can be pulled below ground by as much as 10V without affecting start- up or normal operation. Adjustable Operation The LT3020’s output voltage range is 0.2V to 9.5V. Figure 1 shows that the output voltage is set by the ratio of two external resistors. The device regulates the output to maintain the ADJ pin voltage at 200mV referenced to ground. The current in R1 equals 200mV/R1 and the current in R2 is the current in R1 minus the ADJ pin bias current. The ADJ pin bias current of 20nA flows out of the pin. Use the formula in Figure 1 to calculate output voltage. An R1 value of 20k sets the resistor divider current to 10µA. Note that in shutdown the output is turned off and the divider current is zero. Curves of ADJ Pin Voltage vs Temperature and ADJ Pin Bias Current vs Temperature appear in the Typical Performance Characteristics section. 0.4mV at VADJ= 200mV. At VOUT = 1.5V, load regulation is: (1.5V/200mV) • (0.4mV) = 3mV Output Capacitance and Transient Response The LT3020’s design is stable with a wide range of output capacitors, but is optimized for low ESR ceramic capaci- tors. The output capacitor’s ESR affects stability, most notably with small value capacitors. Use a minimum output capacitor of 2.2µF with an ESR of 0.3Ω or less to prevent oscillations. The LT3020 is a low voltage device, and output load transient response is a function of output capacitance. Larger values of output capacitance decrease the peak deviations and provide improved transient re- sponse for larger load current changes. For output capaci- tor values greater than 20µF a small feedforward capacitor with a value of 300pF across the upper divider resistor (R2 in Figure 1) is required. Give extra consideration to the use of ceramic capacitors. Manufacturers make ceramic capacitors with a variety of dielectrics, each with a different behavior across tempera- ture and applied voltage. The most common dielectrics are Z5U, Y5V, X5R and X7R. The Z5U and Y5V dielectrics provide high C-V products in a small package at low cost, but exhibit strong voltage and temperature coefficients. The X5R and X7R dielectrics yield highly stable characterisitics and are more suitable for use as the output capacitor at fractionally increased cost. The X5R and X7R dielectrics both exhibit excellent voltage coefficient char- acteristics. The X7R type works over a larger temperature range and exhibits better temperature stability whereas X5R is less expensive and is available in higher values. Figures 2 and 3 show voltage coefficient and temperature coefficient comparisons between Y5V and X5R material. Voltage and temperature coefficients are not the only sources of problems. Some ceramic capacitors have a piezoelectric response. A piezoelectric device generates voltage across its terminals due to mechanical stress, simi- lar to the way a piezoelectric accelerometer or microphone works. For a ceramic capacitor, the stress can be induced by vibrations in the system or thermal transients. The re- sulting voltages produced can cause appreciable amounts of noise. A ceramic capacitor produced Figure 4’s trace in response to light tapping from a pencil. Similar vibration induced behavior can masquerade as increased output voltage noise. IN SHDN R2 R1 3020 F01 OUT VIN ADJ GND LT3020-ADJ VOUT + R2 R1 VOUT = 200mV VADJ = 200mV IADJ = 20nA AT 25°C OUTPUT RANGE = 0.2V TO 9.5V 1 + – IADJ (R2) () Figure 1. Adjustable Operation Specifications for output voltages greater than 200mV are proportional to the ratio of desired output voltage to 200mV; (VOUT/200mV). For example, load regulation for an output current change of 1mA to 100mA is typically |
|
|
Enlace URL |
| ¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Enlace a la hoja de datos | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |