K–14

Dimensions are shown: Inch (mm)

Specifications and dimensions subject to change

www.ittcannon.com

K

C&K TM Series

Miniature Snap-acting Switches

ACTUATOR

FIG. 3

A

B

C

Lever

FIG. 4

A

B

C

D

Simulated Roller

—

.600 ± .080

(15,24 ± 2,03)

.58

(14,7)

1.62

(41,1)

3

T25

.25 dia.

(6,4Ø)

.740 ± .090

(18,80 ± 2,29)

.58

(14,7)

1.50

(38,1)

4

T24

.19 dia.

(4,8Ø)

.810 ± .065

(20,57 ± 1,65)

.58

(14,7)

1.56

(39,6)

4

T23

—

.600 ± .045

(15,24 ± 1,14)

.58

(14,7)

1.06

(26,9)

3

T20

—

.600 ± .093

(15,24 ± 2,36)

.36

(9,1)

2.75

(69,9)

3

T18

—

.600 ± .052

(15,24 ± 1,57)

.36

(9,1)

2.00

(50,8)

3

T17

—

.600 ± .062

(15,24 ± 1,57)

.36

(9,1)

2.34

(59,4)

3

T16

—

.600 ± .040

(15,24 ± 1,02)

.36

(9,1)

1.40

(35,6)

3

T15

.25 dia.

(6,4Ø)

.740 ± .050

(18,8 ± 1,3)

.36

(9,1)

1.29

(32,8)

4

T14

.19 dia.

(4,8Ø)

.810 ± .040

(20,57 ± 1,02)

.36

(9,1)

1.34

(34,0)

4

T13

—

.600 ± .020

(15,24 ± 0,51)

.36

(9,1)

.84

(21,3)

3

T10

2.56

(65,0)

T26

HIGH FORCE, LOW MOTION PIVOT POSITION

LOW FORCE, HIGH MOTION PIVOT POSITION

NOTE: Lever actuator options are available in either of two pivot positions.

Levers located in the forward pivot position have lower forces and higher motions.

Levers located in the rear pivot position have higher forces and lower motions.

Available with actuators A10, A15, T10, T13, T14, T15, T16, T17 and T18.

Available with actuators A20, A25, T20, T23, T24, T25, T26, T27 and T28.

FIG. 1

A

B

C

D

Lever Roller

FIG. 2

A

C

Pin Roller

.19 dia.

(4,8Ø)

.810 ± .080

(20,57 ± 2,03)

.58

(14,7)

1.56

(39,6)

1

A25

.19 dia.

(4,8Ø)

.810 ± .050

(20,57 ± 1,27)

.58

(14,7)

1.03

(26,2)

1

A20

.19 dia.

(4,8Ø)

.810 ± .040

(20,57 ± 1,02)

.36

(9,1)

1.34

(34,0)

1

A15

.19 dia.

(4,8Ø)

.810 ± .020

(20,57 ± 0,51)

.36

(9,1)

.81

(20,6)

1

A10

—

.578 ± .015

(14,68 ± 0,38)

—

.80

(20,3)

2

P00

DIM. D

DIM. C

DIM. B

DIM. A

FIG.

OPTION CODE

3

.56

(14,7)

—

.600±.125

(15,24±3.18)

2.22

(56,4)

T27

3

.58

(14,7)

—

.600±.125

(15,24±3.18)

2.97

(75,4)

T28

3

.58

(14,7)

—

.600±.187

(15,24±4.75)