EM6620WS27 datasheet(18/56 Pages) EMMICRO

18 / 56 page

EM6620

www.emmicroelectronic.com

6.4.2 Pull-up/Down

For each terminal of PB[3:0] an internal input pull-up (metal mask MPBPU[n]) or pull-down (metal mask

MPBPD[n]) resistor can be connected per metal mask option. Per default the two resistors are in place. In this

case one can chose per software to have either a pull-up, a pull-down or no resistor. See below.

For Metal mask selection and available resistor values refer to chapter 16.1.2.

Pull-down ON : MPBPD[n] must be in place ,

AND the bit NoPdPB[n] must be ‘0’ .

Pull-down OFF: MPBPD[n] is not in place,

OR if MPBPD[n] is in place NoPdPB[n] = ‘1’ cuts off the pull-down.

OR selecting NchOpDPB[n] = ‘1’ cuts off the pull-down.

Pull-up ON *

: MPBPU[n] must be in place,

AND the bit NchOpDPB[n] must be ‘1’ ,

AND the bit PBIOCntl[n] = ‘0’ (input mode) OR if PBIOCntl[n] = ‘1’ while PBData[n] = 1.

Pull-up OFF*

: MPBPU[n] is not in place,

OR if MPBPU[n] is in place NchOpDPB[n] = ‘0’ cuts off the pull-up,

OR if MPBPU[n] is in place and if NchOpDPB[n] = ‘1’ then PBData[n] = 0 cuts off the pull-up.

Never can pull-up and pull-down be active at the same time.

For POWER SAVING one can switch off the port B pull resistors between two read phases. No cross current

flows in the input amplifier while the port B is not read. The recommended order is :

• switch on the pull resistor.

• allow sufficient time - RC constant - for the pull resistor to drive the line to either VSS or VDD.

• Read the port B

• Switch off the pull resistor

Minimum time with current on the pull resistor is 4 periods of the system clock, if the RC constant is lower than

1 system clock period. Adding a NOP before reading moves the number of periods with current in the pull

resistor to 6 and the maximum RC delay to 3 clock periods.

6.4.3 CMOS / NCH. Open Drain Output

The port B outputs can be configured as either CMOS or Nch. open drain outputs. In CMOS both logic ‘1’ and

‘0’ are driven out on the terminal. In Nch. open drain only the logic ‘0’ is driven out on the terminal, the logic ‘1’

value is defined by the internal pull-up resistor (if implemented) or high impedance.

If using the Dynamic Input Comparator one must put the PB[0] in CMOS input mode and should not use any

pull resistor on this terminal. If not doing so the device may draw excessive current.

Figure 12. CMOS or Open Drain outputs

I / O

Te rm in a l

PB [n ]

MU X

A c tiv e P u llu p

fo r H igh S tate

DR [n ]

F re q uency

Ou tp u ts

Tri-S ta te O u tp u t

B u ffe r : H ig h

Im p e dance fo r

D a ta = 1

I / O

Te rm in a l

PB[n ]

MU X

DR [n ]

F requ enc y

O u tputs

T ri-S tate O u tput

B u ffe r : c los ed

Da ta

C M OS Ou tp u t

N c h. O pen D rain O u tput

EM6620WS27 Datasheet(PDF) 18 Page - EM Microelectronic - MARIN SA

EM6620WS27 Datasheet(HTML) 18 Page - EM Microelectronic - MARIN SA

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56

Datasheet Descarga

Enlace URL