| Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
XR16C2450 Datasheet(PDF) 4 Page - Exar Corporation |
|
|
|||||||||||||||||||||||||||||
XR16C2450 Datasheet(HTML) 4 Page - Exar Corporation |
|
4 / 31 page ![]() XR16C2450 xr 2.97V TO 5.5V DUART REV. 1.0.0 4 RTSA# 32 36 33 O UART channel A Request-to-Send (active low) or general purpose output. If it is not used, leave it unconnected. CTSA# 36 40 38 I UART channel A Clear-to-Send (active low) or general purpose input. This input should be connected to VCC when not used. This input has no effect on the UART. DTRA# 33 37 34 O UART channel A Data-Terminal-Ready (active low) or general purpose output. If it is not used, leave it uncon- nected. DSRA# 37 41 39 I UART channel A Data-Set-Ready (active low) or general purpose input. This input should be connected to VCC when not used. This input has no effect on the UART. CDA# 38 42 40 I UART channel A Carrier-Detect (active low) or general purpose input. This input should be connected to VCC when not used. This input has no effect on the UART. RIA# 39 43 41 I UART channel A Ring-Indicator (active low) or general purpose input. This input should be connected to VCC when not used. This input has no effect on the UART. OP2A# 31 35 32 O Output Port 2 Channel A - The output state is defined by the user and through the software setting of MCR[3]. INTA is set to the active mode and OP2A# output to a logic 0 when MCR[3] is set to a logic 1. INTA is set to the three state mode and OP2A# to a logic 1 when MCR[3] is set to a logic 0. This output should not be used as a general out- put else it will disturb the INTA output functionality. If it is not used at all, leave it unconnected. TXB 12 14 8 O UART channel B Transmit Data. If it is not used, leave it unconnected. RXB 9 10 4 I UART channel B Receive Data. Normal receive data input must idle at logic 1 condition. If it is not used, tie it to VCC or pull it high via a 100k ohm resistor. RTSB# 24 27 22 O UART channel B Request-to-Send (active low) or general purpose output. If it is not used, leave it unconnected. CTSB# 25 28 23 I UART channel B Clear-to-Send (active low) or general purpose input. This input should be connected to VCC when not used. This input has no effect on the UART. DTRB# 34 38 35 O UART channel B Data-Terminal-Ready (active low) or general purpose output. If it is not used, leave it uncon- nected. DSRB# 22 25 20 I UART channel B Data-Set-Ready (active low) or general purpose input. This input should be connected to VCC when not used. This input has no effect on the UART. CDB# 19 21 16 I UART channel B Carrier-Detect (active low) or general purpose input. This input should be connected to VCC when not used. This input has no effect on the UART. Pin Description NAME 40-PDIP PIN # 44-PLCC PIN # 48-TQFP PIN # TYPE DESCRIPTION |
|
Enlace URL |
| ¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Enlace a la hoja de datos | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |