| Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
D301 Datasheet(PDF) 334 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
D301 Datasheet(HTML) 334 Page - Microchip Technology |
|
334 / 416 page ![]() PIC24FJ256GA705 FAMILY DS30010118D-page 334 2016-2018 Microchip Technology Inc. REGISTER 29-5: FOSC CONFIGURATION REGISTER U-1 U-1 U-1 U-1 U-1 U-1 U-1 U-1 — — — — — — — — bit 23 bit 16 U-1 U-1 U-1 U-1 U-1 U-1 U-1 U-1 — — — — — — — — bit 15 bit 8 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 R/PO-1 FCKSM1 FCKSM0 IOL1WAY PLLSS SOSCSEL OSCIOFCN POSCMD1 POSCMD0 bit 7 bit 0 Legend: PO = Program Once bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 23-8 Unimplemented: Read as ‘1’ bit 7-6 FCKSM<1:0>: Clock Switching and Monitor Selection bits 1x = Clock switching and the Fail-Safe Clock Monitor are disabled 01 = Clock switching is enabled, Fail-Safe Clock Monitor is disabled 00 = Clock switching and the Fail-Safe Clock Monitor are enabled bit 5 IOL1WAY: Peripheral Pin Select Configuration bit 1 = The IOLOCK bit can be set only once (with unlock sequence). 0 = The IOLOCK bit can be set and cleared as needed (with unlock sequence) bit 4 PLLSS: PLL Secondary Selection Configuration bit This Configuration bit only takes effect when the PLL is NOT being used by the system (i.e., not selected as part of the system clock source). Used to generate an independent clock out of REFO. 1 = PLL is fed by the Primary Oscillator 0 = PLL is fed by the on-chip Fast RC (FRC) Oscillator bit 3 SOSCSEL: SOSC Selection Configuration bit 1 = Crystal (SOSCI/SOSCO) mode 0 = Digital (SOSCI) Externally Supplied Clock mode bit 2 OSCIOFCN: CLKO Enable Configuration bit 1 = CLKO output signal is active on the OSCO pin (when the Primary Oscillator is disabled or configured for EC mode) 0 = CLKO output is disabled bit 1-0 POSCMD<1:0>: Primary Oscillator Configuration bits 11 = Primary Oscillator mode is disabled 10 = HS Oscillator mode is selected (10 MHz-32 MHz) 01 = XT Oscillator mode is selected (1.5 MHz-10 MHz) 00 = External Clock mode is selected |
|
Enlace URL |
| ¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Enlace a la hoja de datos | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |