| Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
STM32G0 Datasheet(PDF) 90 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
STM32G0 Datasheet(HTML) 90 Page - STMicroelectronics |
|
90 / 135 page ![]() Electrical characteristics STM32G071x8/xB 90/135 DS12232 Rev 4 ENOB Effective number of bits VDDA = VREF+ = 3 V; fADC = 35 MHz; fs ≤ 2.5 MSps; TA = 25 °C 10.1 10.2 - bit 2 V < VDDA = VREF+ < 3.6 V; fADC = 35 MHz; fs ≤ 2.5 MSps; TA = entire range 9.6 10.2 - 1.65 V < VDDA = VREF+ < 3.6 V; TA = entire range Range 1: fADC = 35 MHz; fs ≤ 2.2 MSps; Range 2: fADC = 16 MHz; fs ≤ 1.1 MSps; 9.5 10.2 - SINAD Signal-to-noise and distortion ratio VDDA = VREF+ = 3 V; fADC = 35 MHz; fs ≤ 2.5 MSps; TA = 25 °C 62.5 63 - dB 2 V < VDDA = VREF+ < 3.6 V; fADC = 35 MHz; fs ≤ 2.5 MSps; TA = entire range 59.5 63 - 1.65 V < VDDA = VREF+ < 3.6 V; TA = entire range Range 1: fADC = 35 MHz; fs ≤ 2.2 MSps; Range 2: fADC = 16 MHz; fs ≤ 1.1 MSps; 59 63 - SNR Signal-to-noise ratio VDDA = VREF+ = 3 V; fADC = 35 MHz; fs ≤ 2.5 MSps; TA = 25 °C 63 64 - dB 2 V < VDDA = VREF+ < 3.6 V; fADC = 35 MHz; fs ≤ 2.5 MSps; TA = entire range 60 64 - 1.65 V < VDDA = VREF+ < 3.6 V; TA = entire range Range 1: fADC = 35 MHz; fs ≤ 2.2 MSps; Range 2: fADC = 16 MHz; fs ≤ 1.1 MSps; 60 64 - THD Total harmonic distortion VDDA = VREF+ = 3 V; fADC = 35 MHz; fs ≤ 2.5 MSps; TA = 25 °C --74 -73 dB 2 V < VDDA = VREF+ < 3.6 V; fADC = 35 MHz; fs ≤ 2.5 MSps; TA = entire range --74 -70 1.65 V < VDDA = VREF+ < 3.6 V; TA = entire range Range 1: fADC = 35 MHz; fs ≤ 2.2 MSps; Range 2: fADC = 16 MHz; fs ≤ 1.1 MSps; --74 -70 1. Based on characterization results, not tested in production. 2. ADC DC accuracy values are measured after internal calibration. 3. Injecting negative current on any analog input pin significantly reduces the accuracy of A-to-D conversion of signal on another analog input. It is recommended to add a Schottky diode (pin to ground) to analog pins susceptible to receive negative current. 4. I/O analog switch voltage booster enabled (BOOSTEN = 1 in the SYSCFG_CFGR1) when VDDA < 2.4 V and disabled when VDDA ≥ 2.4 V. Table 58. ADC accuracy(1)(2)(3) (continued) Symbol Parameter Conditions(4) Min Typ Max Unit |
|
Enlace URL |
| ¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Enlace a la hoja de datos | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |