MAX890LCSLASHD datasheet(2/8 Pages) MAXIM

2 / 8 page

1.2A, Current-Limited, High-Side

P-Channel Switch with Thermal Shutdown

_______________________________________________________________________________________

ABSOLUTE MAXIMUM RATINGS

ELECTRICAL CHARACTERISTICS

(VIN = +3V, TA = 0°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C.)

Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional

operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to

absolute maximum rating conditions for extended periods may affect device reliability.

IN to GND ................................................................-0.3V to +6V

ON, FAULT to GND .................................................-0.3V to +6V

SET, OUT to GND ...................................... -0.3V to (VIN + 0.3V)

Maximum Continuous Switch Current ..................................1.5A

Continuous Power Dissipation (TA = +70°C)

SO (derate 5.88mW/°C above +70°C) ..........................471mW

Operating Temperature Range

MAX890LESA ....................................................-40°C to +85°C

Storage Temperature Range ........................... -65°C to +150°C

Lead Temperature (soldering, 10s) . ...............................+300°C

Soldering Temperature (reflow) .......................................+260°C

ON = IN, VIN = VOUT = 5.5V

VIN = 5V

VIN = 3V, IOUT = 500mA

VIN = 5V, ON = GND, IOUT = 0A

VIN = 5V, IOUT = 500mA

20% current overdrive, VCC = 5V

V FAULT = 5.5V, VSET = 1V

VIN = 2.7V to 3.6V

VIN = 2.7V to 5.5V

ISINK = 1mA, VSET = 1.4V

VSET = 1.24V, IOUT = 0A; VIN = VOUT

IOUT = 500mA, VOUT > 1.6V

ON = IN, VIN = 5.5V, VOUT = 0V

Rising edge, 1% hysteresis

VIN = 4.5V

V ON = 5.5V

VSET required to turn the switch off (Note 1)

VIN = 4.5V to 5.5V

CONDITIONS

µs

Turn-Off Time

µs

185

Turn-On Time

120

200

µs

Fast-Current-Loop Response Time

µs

Slow-Current-Loop Response Time

µA

0.05

FAULT Logic Output High Leakage Current

0.4

FAULT Logic Output Low Voltage

µA

0.5

ISET Bias Current

µA

0.01

ON Input Leakage Current

2.4

ON Input High Voltage

µA

0.03

Off-Supply Current

µA

2.7

5.5

Operating Voltage

Quiescent Current

2.0

0.8

ON Input Low Voltage

A/A

970

1110

1300

IOUT to ISET Current Ratio

1.2

Maximum Output Current Limit

µA

0.04

Off-Switch Current

2.0

2.4

2.6

Undervoltage Lockout

130

1.178

1.240

1.302

Current-Limit-Amplifier Threshold

UNITS

MIN

TYP

MAX

PARAMETER

VIN = 3.0V

150

On-Resistance

MAX890LC/D Datasheet(PDF) 2 Page - Maxim Integrated Products

MAX890LC/D Datasheet(HTML) 2 Page - Maxim Integrated Products

Html Pages

1 2 3 4 5 6 7 8

Datasheet Descarga

Enlace URL