MODEL: JAPD2

JAPD2 SPECIFICATIONS

ES-1571 Rev.6 Page 2/4

http://www.m-system.co.jp/

RELATED PRODUCTS

• Programming Unit (model: PU-2x)

• PC configurator software (model: JXCON)

Downloadable at M-System’s web site.

A dedicated cable is required to connect the module to the

PC. Please refer to the internet software download site or

the users manual for the PC configurator for applicable

cable types.

GENERAL SPECIFICATIONS

Construction: Plug-in

Connection: M3.5 screw terminals

Screw terminal: Chromated steel (standard) or stainless

steel

Housing material: Flame-resistant resin (black)

Isolation: Input to alarm output to output to power

Zero adjustment: -5 to +5 % (front)

Span adjustment: 95 to 105 % (front)

Alarm output: Turns on when the input goes above (high) or

below (low) setpoint

Alarm setpoint: -5 – +105 %

Alarm deadband (hysteresis): 0 – 20 %

Output monitor LED: Red LED turns on when the output is

ON or high.

Power ON delay time: 2.0 to 1000.0 sec.

Software programming: Programming Unit (model: PU-2x);

(Refer to the users manual of JXCON for the adjustments

configurable with JXCON)

• Output frequency (zero and span)

• Alarm

• Power ON delay time

• Others

INPUT SPECIFICATIONS

■ DC Current:

Shunt resistor attached to the input terminals (0.5 W)

Specify input resistance value for code Z.

■ DC Voltage: -300 – +300 V DC

Minimum span: 10 mV

Offset: Max. 1.5 times span

Input resistance

Span 10 – 100 mV : ≥ 10 kΩ

Span 0.1 – 1 V : ≥ 100 kΩ

Span ≥ 1 V : ≥ 1 MΩ

OUTPUT SPECIFICATIONS

Frequency range: 100 mHz to 10 kHz (RNG1 to RNG6)

[ Range name : Available frequency ]

RNG1 10 kHz: 0 – 20 kHz

RNG2 1 kHz: 0 – 2 kHz

RNG3 100 Hz: 0 – 200 Hz

RNG4 10 Hz: 0 – 20 Hz

RNG5 1 Hz: 0 – 2 Hz

RNG6 100 mHz: 0 – 200 mHz

Min. span: 10 % of available frequency range

Duty ratio: 50 %

■ Open Collector: 50 V DC @50 mA (resistive load)

Saturation voltage: 0.6 V DC

■ Voltage Pulse

H level: Rating 5, 12 or 24 V ±10 %

L level: ≤ 0.5 V

Load resistance: ≥ 1 kΩ (5 V), ≥ 2.4 kΩ (12 V), ≥ 4.8 kΩ (24

V)

■ Noncontact AC/DC Switch: 120 V AC or 120 V DC @200

mA (resistive load)

ON resistance: 3 Ω max.

Rise time: 5 msec.

Sink time: 3 msec.

■ RS-422 Line Driver Pulse

Transmitter: Conforms to RS-422

■ Relay Contact:

100 V AC @ 1 A (cos ø = 1)

120 V AC @ 1 A (cos ø = 1)

240 V AC @ 0.5 A (cos ø = 1)

30 V DC @ 1 A (resistive load)

Maximum switching voltage: 380 V AC or 125 V DC

Maximum switching power: 120 VA or 30 W

Minimum load: 5 V DC @ 10 mA

INSTALLATION

Power input

•AC: Operational voltage range 85 – 264 V, 47 - 66 Hz;

Approx. 3.2 VA at 100 V

Approx. 5.1 VA at 200 V

Approx. 6.9 VA at 264 V

•DC: Operational voltage range: rating ±10 %, or 85 – 150 V

for 110 V rating (ripple 10 % p-p max.)

Approx. 2.5 W (100 mA at 24 V)

Operating temperature: -5 to +55°C (23 to 131°F)

Operating humidity: 30 to 90 %RH (non-condensing)

Mounting: Surface or DIN rail

Weight: 280 g (0.62 lb)