BLUENRG-LP datasheet(17/72 Pages) STMICROELECTRONICS

17 / 72 page

•

Priorities among requests from channels of DMA are software programmable (four levels consisting of very

high, high, medium, low) or hardware in case of equality (request 1 has priority over request 2, and so on)

•

Independent source and destination transfer size (byte, half word, word), emulating packing and unpacking.

Source/destination addresses must be aligned on the data size

•

Support for circular buffer management

•

Three event flags (DMA half transfer, DMA transfer complete and DMA transfer error) logically ORed

together in a single interrupt request for each channel

•

Memory-to-memory transfer (RAM only)

•

Peripheral-to-memory and memory-to-peripheral, and peripheral-to-peripheral transfers

•

Access to SRAMs and APB1 peripherals as source and destination

•

Programmable number of data to be transferred: up to 65536

1.14

Nested vectored interrupt controller (NVIC)

The interrupts are handled by the Cortex®-M0+ nested vector interrupt controller (NVIC). NVIC controls specific

Cortex®-M0+ interrupts as well as the BlueNRG-LP peripheral interrupts.

The NVIC benefits are the following:

•

Nested vectored interrupt controller that is an integral part of the ARM® Cortex®-M0+

•

Tightly coupled interrupt controller provides low interrupt latency

•

Control system exceptions and peripheral interrupts

•

NVIC supports 32 vectored interrupts

•

Four programmable interrupt priority levels with hardware priority level masking

•

Software interrupt generation using the ARM® exceptions SVCall and PendSV

•

Support for NMI

•

ARM® Cortex® M0+ vector table offset register VTOR implemented

NVIC hardware block provides flexible interrupt management features with minimal interrupt latency.

1.15

Analog digital converter (ADC)

The BlueNRG-LP embeds a 12-bit ADC. The ADC consists of a 12-bit successive approximation analog-to-digital

converter (SAR) with 2 x 8 multiplexed channels allowing measurements of up to eight external sources and up to

two internal sources.

It embeds a PDM interface integrating a digital filter for processing PDM stream coming from a digital microphone.

It also embeds a dedicated ECM microphone feature with which it is possible to connect an analog microphone

directly to the ADC port of the BlueNRG-LP.

The ADC main features are:

•

Conversion frequency is up to 1 Msps

•

Three input voltage ranges are supported (0 - 1.2 V, 0 - 2.4 V, 0 - 3.6 V)

•

Up to eight analog single-ended channels or four analog differential inputs or a mix of both

•

One analog microphone supported through two GPIOs configured in analog mode (an input for the analog

microphone and a Vbias output for the analog microphone)

•

Temperature sensor conversion

•

Battery level conversion up to 3.6 V

•

Continuous or single acquisition

•

Digital decimation filter to process a digital audio PDM stream provided by 2 GPIOs and for ADC post-

processing, especially for analog audio stream

•

Five modes of conversion are possible:

–

ADC continuous or single mode

–

Analog continuous audio mode

–

Occasional conversions

–

Digital continuous audio mode

–

Full mode

BlueNRG-LP

Nested vectored interrupt controller (NVIC)

DS13282 - Rev 2

page 17/72

BLUENRG-LP Datasheet(PDF) 17 Page - STMicroelectronics

BLUENRG-LP Datasheet(HTML) 17 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72

Datasheet Descarga

Enlace URL