V13

2

Specifications

CFM80S Series Derating Curve

INPUT SPECIFICATIONS:

Voltage …....………........…......................................................... 90~264Vac

120~370Vdc

Frequency …………………………..…..………………………..... 47 to 63Hz

Inrush Current ………………….…… Cold start @25℃100A max. @240Vac

Input Current ……….……………..…. 100Vac/1.5A max., 240Vac/0.8A max.

Leakage Current ……………………..………………….…...…… 3.5mA max.

OUTPUT SPECIFICATIONS:

Holdup Time …………………………..……………….… 12mS typ. @115Vac

Short Circuit Protection …………………….... Hiccup Mode (Auto Recover)

Over Voltage Protection ………………...……..... TVS Component to Clamp

Temperature Coefficient ……………………................................. ±0.05%/℃

GENERAL SPECIFICATIONS:

Isolation ……………………..……………….…… Input to output = 3000VAC

Operating Temperature ............................ -20 ~ 80℃ (see derating curve)

Derating curve for Natural Convection

0%

25%

50%

75%

100%

-20 -10

0

10

20

30

40

50

60

70

80

20LFM(Natural Convection)

Storage Temperature …………………………....….........…........ -20℃~85℃

NOTE:

Humidity ..................................................... 93% RH max. Non-Condensing

1. Voltage accuracy is set at full load.

Cooling ………………………..…………………..……..... Natural Convection

2. Add a 0.1uF ceramic capacitor and a 10uF E.L. capacitor to output for

Switching Frequency ………………………………….……. 100KHz Typical

ripple&noise measurement @20MHz BW.

Dimensions

3. Line regulation is measured from high line to low line with full load.

Open Frame ……….. 4.000x2.000x1.07 inches (101.6x50.8x27.1 mm)

4. Load regulation is measured from 10% to 100% full load.

-P ……………..… 4.000x2.000x1.142 inches (101.6x50.8x29.00 mm)

5. Typical efficiency at 230 VAC and full load at 25°C.

Weight ……………………………….……..………………………...…… 155g

6. Standard input and output connectors (CN1 and CN2) wafer with

SAFETY AND EMC:

TAIWAN KING PIN TERMINAL PVHI series and mate with JST

Emission and lmmunity ………… EN55032 Class B, FCC Part 15 Class B

housing VHR series and JST SVH-21/41T-P1.1 series crimp terminal

EN61000-6-3, EN61000-3-2, EN61000-3-3

or equivalent.

EN 5 5 0 2 4 , E N 6 1 2 0 4- 3 , EN 6 1 0 0 0 - 6 - 1

Safety …………………… Class I, IEC/EN/UL60950-1, IEC/EN/UL62368-1

Mechanical Specification

6

5

4

3

2

1

Neutral

2

Function

Pin

PIN CONNECTION

6

5

Vout(-)

Vout(-)

4

Vout(+)

3

Vout(+)

2

Vout(+)

1

Function

Pin

PIN CONNECTION

CN2:

3.645[92.58]

0.165[4.19]

0.039[1.00]

0.071[1.80]

3.700[93.98]

4.000[101.60]

0.150[3.81]

1

2

CN2

CN1

ACL

ACN

1

Line

CN1:

Vout(-)

4.000[101.60]

3.700[93.98]

All Dimensions in Inches[mm]

Tolerance Inches:x.xxx±0.02

Millimeters:x.xx±0.5

PE

ACL 1

2

ACN 3

CN1

VR

0.150[3.81]

CN2

1

2

3

4

5

6

PE

CFM80SXXX

CFM80SXXX-P

(Input/Output Connector with PIN)

VR

PE

PE

Typical at 25˚C, nominal line and 75% load, unless otherwise Specified